Published Nov 20, 2026 · Last updated Nov 20, 2026 · 6 min · IndieRF
Blocker Desense: +18.7 dBm, Set by LO Noise
Reciprocal mixing beats mixer compression by 3.1 dB.
Wi-Fi channel 1 behind a Qorvo 885128 takes an LTE Band 40 blocker at 2362 MHz up to +18.7 dBm, set by reciprocal mixing on its HMC832A LO; mixer compression allows +21.8 dBm. A one-gain spreadsheet row says −9.5 dBm.
One filter, two carriers
The lineup is the 885128 coexistence filter, an HMC8413 LNA, and an HMC213B mixer with a low-side LO at 2000 MHz, so the IF is 412 MHz. Qorvo's Rev B sheet guarantees, from −30 to +85 °C, 1.7 dB maximum loss across channel 1 and 33 dB minimum rejection over 2300 to 2370 MHz. The wanted carrier pays 1.7 dB and the blocker pays 33.
A spreadsheet stage is one row with one gain. Put the filter in as 1.7 dB and the blocker reaches the LNA 31.3 dB hotter than it really does; put it in as 33 dB and the wanted signal loses 31.3 dB it never lost. Cascade carries the blocker and the wanted carrier as separate carriers and reads the filter's curve at each one's frequency, which is the whole difference between −9.5 dBm and +21.8 dBm.
Compression comes from the HMC213B, whose input P1dB is 11 dBm at 13 dBm LO. A weak carrier beside a strong one loses more gain than the strong one does: on a memoryless Rapp curve its gain is the average of the slope and the chord, so it reaches 1 dB of desense while the blocker itself is only 0.34 dB compressed at the mixer. The panel's HMC8413 row needs +33.3 dBm, so the mixer compresses 11.5 dB sooner.
Reciprocal mixing from the LO table
The blocker mixes with the LO's phase noise at the blocker's offset and lands that noise on the channel. The HMC832A sheet, Rev. B, Table 1, prints open-loop VCO phase noise at 2 GHz: −157 dBc/Hz at 10 MHz and −162 dBc/Hz at 100 MHz. Open loop is the right number this far out, since any PLL loop is far narrower than 50 MHz. On a straight log-log line that is −160.5 dBc/Hz at 50 MHz, and integrated from 40 to 60 MHz offset, the 20 MHz channel, −87.46 dBc. Referred to the antenna port:
where is the filter's rejection of the blocker less its loss on the wanted carrier, 31.3 dB. That is the panel's "blocker level − 118.76 dB".
The budget gives a cumulative NF of 6.73 dB at the mixer, a floor of −94.2 dBm in 20 MHz. The HMC213B sheet prints no noise figure, so the budget takes the passive-mixer convention, NF equal to its 10 dB conversion loss. If the real NF is 2 dB higher, the cumulative NF is 6.82 dB and the floor −94.1 dBm, which moves the answer 0.09 dB to +18.8 dBm; the LNA's 19.5 dB hides most of the mixer. Mixing noise costs 1 dB when it sits 5.9 dB under the floor, at −100.1 dBm, which takes a +18.7 dBm blocker. Compression at that level is 0.25 dB, so reciprocal mixing sets the limit by 3.1 dB. A +23 dBm handset transmitter beside the receiver needs 4.3 dB of antenna isolation to stay under it. The same printed phase noise table that sets an ADC clock's jitter in the jitter note sets this; here only one offset matters.
Rule of thumb: reciprocal mixing costs 1 dB when blocker level plus L at the offset plus 10·log10(BW) sits 5.9 dB under the noise floor, both referred to the same plane, and each dB of filtering ahead of the mixer buys a dB. It breaks close in, where L changes across the channel and the flat-L sum misreads the integral.
Other blockers on the same lineup
Every row is Cascade's Blocker and desense panel on the linked lineup with the offset typed in, checked against the Rapp weak-tone form and the mask integral worked by hand. Levels are at the filter input for 1 dB of desense.
| Blocker | Offset (MHz) | 885128 loss (dB) | Compression, 1 dB (dBm) | Reciprocal mixing, 1 dB (dBm) |
|---|---|---|---|---|
| LTE Band 40, 2362 MHz | −50 | 33 | +21.8 | +18.7 |
| LTE Band 40, 2332 MHz | −80 | 33 | +21.8 | +19.7 |
| LTE Band 41, 2500 MHz | +88 | 23 | +11.8 | +9.9 |
| Wi-Fi channel 6, 2437 MHz | +25 | 1.5 | −9.7 | −14.4 |
| One-gain sheet row, 2362 MHz | −50 | 1.7 | −9.5 | −12.6 |
Reciprocal mixing sets the limit on every row, by 1.9 to 4.7 dB. Band 41 is the weak side of this filter: the 2500 to 2505 MHz row guarantees 23 dB below 25 °C and 31 dB above, so a cold board loses 8 dB of blocker margin. A Wi-Fi neighbour on channel 6 sits in the passband and takes only the filter's 1.5 dB, so −14.4 dBm is the whole story; that one is the LO's to fix.
What the floor does to the answer
This lineup has no image filter between the LNA and the mixer, so the LNA's noise at the 1588 MHz image folds into the IF and the NF is 6.73 dB instead of 3.84 dB. Fit one and the floor drops 2.9 dB, and the reciprocal-mixing limit drops with it to +15.8 dBm. A quieter receiver tolerates less blocker in absolute terms, because the mixing noise is the same and the floor it is measured against moved. The image noise note works that side.
Cascade's reciprocal-mixing line is a scalar estimate at small-signal gains and is not added to the budget's noise, so the budget's NF and SNR rows stay at 6.73 dB with the blocker present; the 1 dB criterion above is worked from the panel's line and the budget's floor. The panel's offset is typed by hand each time, since the link carries the lineup and the LO mask but the panel saves no setting. The LO also needs a buffer from the HMC832A's 7 dBm maximum to the mixer's 13 dBm, and that buffer's own noise floor adds to the mask above.
References
- Qorvo, 885128 2.4 GHz WLAN/BT LTE Co-Existence Filter, Preliminary Data Sheet Rev B 07-21-15, page 2, Electrical Specifications, −30 to +85 °C.
- Analog Devices, HMC832A Fractional-N PLL with Integrated VCO, 25 MHz to 3000 MHz, data sheet Rev. B, page 5, Table 1, VCO open-loop phase noise, fO at 2 GHz (gain setting 6, high performance mode).
- Analog Devices, HMC8413 Low Noise Amplifier, 0.01 GHz to 9 GHz, data sheet Rev. 0, 10/2021, page 3, Table 1.
- Analog Devices, HMC213BMS8E Double Balanced Mixer, 1.5 GHz to 4.5 GHz, data sheet Rev. 0, 2/2018, page 3, Table 1.
Related
Questions? Contact
Discussion
No comments yet. Start the thread with a measurement, a correction, or a worked example.