IndieRF VSWR Converter

VSWR to return loss converter

VSWR 2 is 9.54 dB return loss, |Γ| = 0.333, and 0.51 dB of mismatch loss. Type any one of VSWR, return loss, |S11| in dB, |Γ|, mismatch loss, or reflected power and read the other five, then print the VSWR 1.01 to 10 table or download it as a CSV.

Loading the calculator…

One reflection, six readings

VSWR 2 is 9.54 dB return loss, |Γ| = 0.3333, and 0.51 dB of mismatch loss. Return loss, |S11| in dB, |Γ| and VSWR are the same reflection coefficient in four units. Mismatch loss and reflected power answer a different question: how much of the available power fails to arrive.

Rule of thumb: 2:1 VSWR is half a dB. 10 dB return loss is 0.46 dB. It breaks when there are two mismatched ports in a row, because their reflections add or cancel and the cascade sees a ripple around that number. Budget the ripple, not the half dB, when a filter faces an antenna.

A 10 dB return-loss mask is a 0.46 dB power problem. The ten decibels are how far down the reflection is, so a radio that lands at 9 dB has given up a few hundredths more, not an extra decibel of link budget. The return loss, VSWR and mismatch loss note works that row on two real loads.

Pads and return loss

A pad buys twice its value in return loss, because the reflection crosses it twice. A 10 dB pad in front of a 10 dB load should show 30 dB. Its own match caps that: a pad specified at 1.2:1 VSWR is 20.83 dB return loss by itself, and it costs you 10 dB of signal.

Limits

Every field assumes a real reference impedance, usually 50 Ω, and mismatch loss assumes a source equal to it. With a complex source the delivered power is the transducer gain of the full network, which Smith Chart & Matching reports. Entries outside a field's range are held at the limit with a note that says what the entry would mean: VSWR below 1, |Γ| above 1, a negative return loss, or a positive S11 in dB.

Checked against scikit-rf: the cases, the tolerance and what the check does not cover.

FAQ

How do I convert VSWR to return loss?

Find |Γ| = (VSWR − 1) / (VSWR + 1), then return loss = −20·log10|Γ|. VSWR 2 is |Γ| = 0.3333 and 9.54 dB return loss. VSWR 1.5 is 13.98 dB, and VSWR 3 is 6.02 dB.

How much power does VSWR 2 lose?

11.11% of the incident power reflects, so the load keeps 88.89%, a mismatch loss of 0.51 dB. That holds for a real source equal to the reference impedance and no other mismatch in the path.

Is |S11| in dB the same as return loss?

Same number, opposite sign. A VNA trace reads S11 in dB, which is negative for a passive port: −10 dB on the trace is 10 dB return loss, |Γ| = 0.3162. A positive S11 in dB means the port returns more power than it receives, an amplifier or an oscillating port.

What return loss is a good match?

10 dB is a common antenna mask: VSWR 1.92 and 0.46 dB of mismatch loss. 14 dB is VSWR 1.50 and 0.18 dB. 20 dB is VSWR 1.22 and 0.044 dB. Past 20 dB the power gain is a few hundredths of a dB, so the spec, the cable, and the connector decide.

Question or a correction?