IndieRF Attenuator Pad Calculator
Attenuator pad calculator
A 50 Ω 3 dB pi pad is 292.4 Ω shunt and 17.61 Ω series. Pick pi, T, bridged-T or the minimum-loss pad, type the loss and the impedance at each end, and read the exact values, the nearest E24 and E96 parts, the loss and return loss those parts give, and the power in each resistor.
Attenuator resistor table, 1 to 30 dB at 50 Ω and 75 Ω
Exact values for equal ends. The bridged-T series arms are the line impedance itself, so only the bridge and the shunt change. Each dB value opens the calculator at that loss with E24 and E96 parts.
50 Ω
| dB | Pi (Ω) | T (Ω) | Bridged-T (Ω) | |||
|---|---|---|---|---|---|---|
| Shunt | Series | Series | Shunt | Bridge | Shunt | |
| 1 | 869.5 | 5.769 | 2.875 | 433.3 | 6.101 | 409.8 |
| 2 | 436.2 | 11.61 | 5.731 | 215.2 | 12.95 | 193.1 |
| 3 | 292.4 | 17.61 | 8.550 | 141.9 | 20.63 | 121.2 |
| 4 | 221.0 | 23.85 | 11.31 | 104.8 | 29.24 | 85.49 |
| 5 | 178.5 | 30.40 | 14.01 | 82.24 | 38.91 | 64.24 |
| 6 | 150.5 | 37.35 | 16.61 | 66.93 | 49.76 | 50.24 |
| 7 | 130.7 | 44.80 | 19.12 | 55.80 | 61.94 | 40.36 |
| 8 | 116.1 | 52.84 | 21.53 | 47.31 | 75.59 | 33.07 |
| 9 | 105.0 | 61.59 | 23.81 | 40.59 | 90.92 | 27.50 |
| 10 | 96.25 | 71.15 | 25.97 | 35.14 | 108.1 | 23.12 |
| 11 | 89.24 | 81.66 | 28.01 | 30.62 | 127.4 | 19.62 |
| 12 | 83.54 | 93.25 | 29.92 | 26.81 | 149.1 | 16.77 |
| 13 | 78.84 | 106.1 | 31.71 | 23.57 | 173.3 | 14.42 |
| 14 | 74.93 | 120.3 | 33.37 | 20.78 | 200.6 | 12.46 |
| 15 | 71.63 | 136.1 | 34.90 | 18.36 | 231.2 | 10.81 |
| 16 | 68.83 | 153.8 | 36.32 | 16.26 | 265.5 | 9.417 |
| 17 | 66.45 | 173.5 | 37.62 | 14.41 | 304.0 | 8.224 |
| 18 | 64.40 | 195.4 | 38.82 | 12.79 | 347.2 | 7.201 |
| 19 | 62.64 | 220.0 | 39.91 | 11.36 | 395.6 | 6.319 |
| 20 | 61.11 | 247.5 | 40.91 | 10.10 | 450.0 | 5.556 |
| 21 | 59.78 | 278.3 | 41.82 | 8.984 | 511.0 | 4.892 |
| 22 | 58.63 | 312.7 | 42.64 | 7.994 | 579.5 | 4.314 |
| 23 | 57.62 | 351.4 | 43.39 | 7.115 | 656.3 | 3.809 |
| 24 | 56.73 | 394.6 | 44.06 | 6.335 | 742.4 | 3.367 |
| 25 | 55.96 | 443.2 | 44.68 | 5.641 | 839.1 | 2.979 |
| 26 | 55.28 | 497.6 | 45.23 | 5.024 | 947.6 | 2.638 |
| 27 | 54.68 | 558.6 | 45.72 | 4.476 | 1069 | 2.338 |
| 28 | 54.15 | 627.0 | 46.17 | 3.987 | 1206 | 2.073 |
| 29 | 53.68 | 703.7 | 46.57 | 3.553 | 1359 | 1.839 |
| 30 | 53.27 | 789.8 | 46.93 | 3.165 | 1531 | 1.633 |
75 Ω
| dB | Pi (Ω) | T (Ω) | Bridged-T (Ω) | |||
|---|---|---|---|---|---|---|
| Shunt | Series | Series | Shunt | Bridge | Shunt | |
| 1 | 1304 | 8.654 | 4.313 | 650.0 | 9.151 | 614.7 |
| 2 | 654.3 | 17.42 | 8.597 | 322.9 | 19.42 | 289.7 |
| 3 | 438.6 | 26.42 | 12.82 | 212.9 | 30.94 | 181.8 |
| 4 | 331.5 | 35.77 | 16.97 | 157.2 | 43.87 | 128.2 |
| 5 | 267.7 | 45.60 | 21.01 | 123.4 | 58.37 | 96.37 |
| 6 | 225.7 | 56.03 | 24.92 | 100.4 | 74.64 | 75.36 |
| 7 | 196.1 | 67.20 | 28.69 | 83.70 | 92.90 | 60.55 |
| 8 | 174.2 | 79.27 | 32.29 | 70.96 | 113.4 | 49.61 |
| 9 | 157.5 | 92.38 | 35.72 | 60.89 | 136.4 | 41.25 |
| 10 | 144.4 | 106.7 | 38.96 | 52.70 | 162.2 | 34.69 |
| 11 | 133.9 | 122.5 | 42.02 | 45.92 | 191.1 | 29.43 |
| 12 | 125.3 | 139.9 | 44.89 | 40.22 | 223.6 | 25.16 |
| 13 | 118.3 | 159.1 | 47.56 | 35.35 | 260.0 | 21.63 |
| 14 | 112.4 | 180.5 | 50.05 | 31.17 | 300.9 | 18.69 |
| 15 | 107.4 | 204.2 | 52.35 | 27.55 | 346.8 | 16.22 |
| 16 | 103.3 | 230.7 | 54.48 | 24.39 | 398.2 | 14.13 |
| 17 | 99.67 | 260.2 | 56.43 | 21.62 | 456.0 | 12.34 |
| 18 | 96.60 | 293.2 | 58.23 | 19.19 | 520.7 | 10.80 |
| 19 | 93.96 | 330.0 | 59.87 | 17.04 | 593.4 | 9.479 |
| 20 | 91.67 | 371.3 | 61.36 | 15.15 | 675.0 | 8.333 |
| 21 | 89.68 | 417.4 | 62.73 | 13.48 | 766.5 | 7.338 |
| 22 | 87.94 | 469.1 | 63.96 | 11.99 | 869.2 | 6.472 |
| 23 | 86.43 | 527.0 | 65.08 | 10.67 | 984.4 | 5.714 |
| 24 | 85.10 | 592.0 | 66.10 | 9.502 | 1114 | 5.051 |
| 25 | 83.94 | 664.7 | 67.01 | 8.462 | 1259 | 4.469 |
| 26 | 82.91 | 746.3 | 67.84 | 7.537 | 1421 | 3.957 |
| 27 | 82.01 | 837.8 | 68.59 | 6.714 | 1604 | 3.507 |
| 28 | 81.22 | 940.5 | 69.26 | 5.981 | 1809 | 3.110 |
| 29 | 80.52 | 1056 | 69.86 | 5.329 | 2039 | 2.759 |
| 30 | 79.90 | 1185 | 70.40 | 4.748 | 2297 | 2.449 |
Pi, T or bridged-T
With exact values all three lose the same and match both ends. The parts differ. At 50 Ω and 20 dB a pi needs 61.11 Ω shunts and a 247.5 Ω series resistor, a T needs 40.91 Ω series arms and a 10.10 Ω shunt, and a bridged-T needs a 450.0 Ω bridge and a 5.556 Ω shunt beside two 50 Ω arms. The bridged-T arms never change, and its bridge times its shunt is always Z0², so a variable one moves two parts together.
What standard parts cost
Build the 50 Ω 10 dB pi from E24 100 Ω and 68 Ω parts and it loses 9.63 dB with 49.6 dB return loss. The standard parts move the loss by 0.37 dB. When the loss itself matters, the calculator shows the E96 build next to it.
Pads and return loss
A pad buys twice its value in return loss. A 10 dB pad in front of a 10 dB return-loss load should show 30 dB, because the reflection crosses the pad twice. The pad's own match caps it: a pad specified at 1.2:1 VSWR is 20.83 dB return loss by itself, and it costs you 10 dB of signal. The VSWR converter turns a datasheet VSWR into return loss.
Between unequal ends
A resistive pad from 50 Ω to 75 Ω loses at least 5.72 dB. That minimum is an L pad: 43.30 Ω in series on the 75 Ω side and 86.60 Ω in shunt across the 50 Ω side. Ask a pi or T for less and one resistor would have to be negative; ask for more and they take over with three positive values.
Equations
A is the loss in dB, N = 10^(A/10) the power ratio and K = √N. Port 1 sees Z1 and port 2 sees Z2.
- Pi: series = (N − 1)/2 · √(Z1·Z2/N); shunt at port i = 1 / ((N + 1)/(Zi(N − 1)) − 1/series)
- T: shunt = 2√(N·Z1·Z2)/(N − 1); series at port i = Zi(N + 1)/(N − 1) − shunt
- Bridged-T (Z1 = Z2 = Z0): arms Z0, bridge Z0(K − 1), shunt Z0/(K − 1)
- Minimum loss, r = Zhigh/Zlow: A = 20·log10(√r + √(r − 1))
- Minimum-loss L: series √(Zhigh(Zhigh − Zlow)), shunt Zlow·√(Zhigh/(Zhigh − Zlow))
The loss and return loss of a built pad come from a nodal solve of its resistors between a Z1 source and a Z2 load. That solve is checked against the same resistors in scikit-rf on 153 pads, exact and built from E24 and E96 parts, to 1e-12 in S11, S21 and S22. The resistors are ideal and the port impedances real: at high frequency the parts' parasitics and the layout set the match, and this page does not model them.
Checked against scikit-rf: the cases, the tolerance and what the check does not cover.
FAQ
What resistors make a 3 dB 50 Ω attenuator?
A pi pad with 292.4 Ω shunt resistors at each end and 17.61 Ω in series. The nearest E96 parts are 294 Ω and 17.8 Ω.
What is the minimum-loss pad from 50 Ω to 75 Ω?
43.30 Ω in series on the 75 Ω side and 86.60 Ω in shunt across the 50 Ω side. It loses 5.72 dB, the least any resistive pad between those impedances can lose, and matches both ends.
How much power does each resistor in a pad take?
With 1 W into a 50 Ω 3 dB pi, the series resistor takes 242 mW, the input shunt 171 mW and the output shunt 85.7 mW. Type your input power in the calculator for the same column at your level.