RG-178 cable loss (Belden 83265)

Belden 83265 loses 5.48 dB per 10 m at 144 MHz and 23.5 dB at 2.4 GHz (extrapolated). The part is Belden 83265, RG-178, PTFE, commercial non-QPL (M17/93-RG178), and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

Belden 83265 loss for 10.0 m, matched

0.10.31310301001 MHz10 MHz100 MHz1 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
23.52 dB
Out of 100 W
445 mW
Delivered
0.44%

Extrapolated. Extrapolated 2.4× past the last printed row at 1 GHz.

Neighbours at 2.40 GHz

  1. Belden 8328415.50 dB
  2. Belden 821619.76 dB, extrapolated
  3. Belden 8326523.52 dB, extrapolated

Rank 24 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of Belden 83265 (RG-178) against frequency, per 10 m and per 100 ft: 5.48 dB per 10 m at 144 MHz and 23.5 dB per 10 m at 2.4 GHz (extrapolated).
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz5.4816.7printed
433 MHz9.6229.3printed
915 MHz14.243.2printed
1.09 GHz15.547.3extrapolated
2.4 GHz23.571.7extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 1.8 mmDielectric⌀ 0.838 mmCentre conductor⌀ 0.305 mm0.5 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.601.84
3.5 MHz0.842.57
7 MHz1.193.63
14 MHz1.695.15
28 MHz2.397.29
50 MHz3.219.77
144 MHz5.4816.7
433 MHz9.6229.3
915 MHz14.243.2
1.57 GHz18.857.4extrapolated
2.4 GHz23.571.7extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printed
12.61.370-1.230
105.64.345-1.255
5010.59.770-0.730
1001413.87-0.126
2001919.74+0.736
4002828.14+0.139
7003737.56+0.557
90042.542.79+0.292
10004645.21-0.793

Belden 83265 technical data sheet, accessed 2026-10-11. Belden 83265, RG-178, PTFE, commercial non-QPL (M17/93-RG178).

α (dB/m) = a·√f + b·f with f in GHz: a = 1.419, b = 0.06393. Least squares over the 9 printed rows. RMS miss 0.762 dB/100 ft, largest 1.255 dB/100 ft at 10.0 MHz.

Usable range and build

Printed from 1 MHz to 1 GHz. Usable from 1 MHz to 4 GHz; the top is set by the 4× the last printed row. TE11 cutoff 116.9 GHz, from the printed diameters and velocity factor.

Maker
Belden
RG name on the sheet
RG-178
Impedance
50 Ω
Velocity factor
0.7
Delay
4.77 ns/m
Dielectric
PTFE
Centre conductor
0.012 in (0.305 mm)
Dielectric diameter
0.033 in (0.838 mm)
Jacket OD
1.8 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
5 lb/1000 ft
Bend radius, installed
1 in (25.4 mm)
Bend radius, repeated
not printed
Shield
Silvered copper braid, 95%
  • Attenuation is printed through 1000 MHz. The sheet prints no maximum operating frequency.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?