IndieRF Transmission Line Calculator

Microstrip insertion loss and 50 Ω width

Find the width of a 50 Ω microstrip on your stackup, then read impedance, loss, and delay. Copper finish, foil roughness, and solder mask are included.

Loading the calculator…

How to use

  1. Choose the laminate and type the dielectric height from the stackup, or pick a fab stackup. A four-layer preset uses the outer dielectric over layer 2.
  2. Set copper weight, finish, foil, and whether the mask is flooded, windowed, or absent.
  3. Leave the lock on to solve the width, or type the width from the fab drawing.
  4. Read Z0 and loss first. Delay and ε_eff are for length matching. The TE1 figure is the rough top of the single-mode band.

Worked example

RO4350B, 6.6 mil, 17.5 µm copper, ENIG, reverse-treated foil, Huray roughness, relieved mask, 10 GHz. This engine solves a 13.69 mil trace at 50.00 Ω, with ε_eff 2.805, loss 0.563 dB/in, and delay 141.89 ps/in. The TE1 estimate is 548.2 GHz.

Models used

A 2-D quasi-static field solve gives the static impedance and ε_eff(0), copper thickness and solder mask included, within 0.05% of a converged reference. Hammerstad–Jensen shows, labeled, while it runs. Kirschning–Jansen slides ε_eff up toward εr as frequency rises, and the impedance falls as the square root of that ratio. Conductor loss uses the surface impedance of the plating stack. Roughness multiplies the copper term. The model is quasi-TEM. Trust it when the width is about 0.1 to 10 times the height and the frequency is below the TE1 estimate.

A match at the end of the line is a different tool. Open the Smith chart. The finish comparison is written up in the ENIG versus copper note.

How wide is 50 Ω on FR-4?

On this library’s FR-4 (εr 4.4), 1 oz copper, no solder mask, at 1 GHz, a 50 Ω microstrip is 118.33 mil (3.006 mm) when the dielectric is the full 1.6 mm, and 14.66 mil (0.372 mm) over a 0.2104 mm prepreg. The finished board thickness is not the height the strip sees. An edge-coupled pair on the same microstrip uses the Differential pair topology.

How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.

FAQ

How do I find a 50 Ω microstrip width?

Set the substrate and the core height from your fabricator, then leave Lock to 50 Ω on. The width box shows the trace that hits 50 Ω at the evaluation frequency. Turn the lock off if the drawing already specifies the width.

Why did the impedance change when I added solder mask?

Mask is a dielectric sitting on the trace. Flooding it adds capacitance, so Z0 falls and a little loss appears. A windowed relief pulls the mask back and moves both numbers toward the bare line. The calculator solves the coat over the trace top and both sidewalls in a 2-D field solve. On JLC04161H-7628 the 0.6 mil mask takes the 50 Ω width from 12.31 to 11.66 mil.

What is effective permittivity used for?

ε_eff is the permittivity the wave actually sees, between 1 and the substrate εr because some field is in air. Delay and wavelength both come from it. Use it when two traces must be the same electrical length.

Which model is this microstrip calculator using?

Static impedance and ε_eff come from a 2-D quasi-static field solve of the cross-section in your browser, with the copper thickness and a conformal solder mask. Against a converged reference it is within 0.05%. Hammerstad and Jensen, IEEE MTT-S 1980, shows while the solve runs, and alone for a zero-thickness bare strip. Frequency dependence uses Kirschning and Jansen, Electronics Letters, 1982. Plating and roughness sit on top of that line.