ESP32-C3 Antenna Matching: 35 Ω Target and CLC Ranges
Espressif's target for the ESP32-C3 RF pin is 35+j0 Ω, read as S11 from the chip end of the matching circuit. The guide prints a CLC pi with L2 2.0 ~ 3.0 nH in series and capacitors of 1.2 ~ 1.8 pF and 1.8 ~ 1.2 pF, under designators its own figure does not use.
Target at the chip end: 35 Ω (printed 35+j0)
“If S11 is close to the chip conjugate point 35+j0 and S21 is less than -35 dB at 4.8 GHz and 7.2 GHz, the matching circuit can satisfy transmission requirements.”
Read as S11 at port 1 of the matching circuit, the port near the chip, on a network analyzer. ESP32-C3 Hardware Design Guidelines v1.8 (2025-06-05), Schematic Checklist, RF Tuning, page 11.
Open in Match with 35 Ω at the chip and a 50 Ω trace
Espressif prints no frequency with the target, so Match opens at its 2.45 GHz default. Type your channel in f0 and Match redraws the L-network.
Recommended value ranges
For a PCB that follows the guide's PCB Layout Design chapter. 0201 parts. Table 2 names C11, L2 and C12.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C11 | 1.2 ~ 1.8 pF | Not on Figure 7 | GRM0335C1H1RXBA01D |
| L2 | 2.0 ~ 3.0 nH | Series | LQP03TN2NXB02D |
| C12 | 1.8 ~ 1.2 pF | Not on Figure 7 | GRM0335C1H1RXBA01D |
ESP32-C3 Hardware Design Guidelines v1.8 (2025-06-05): Table 2 (Recommended Value Ranges for Components), page 11.
Chip matching circuit, as drawn (CLC)
Figure 7. Every value is TBD on the figure. C9 shunt at the chip pin, L2 in series, C8 shunt toward the antenna.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C9 | TBD | Shunt at the chip pin (LNA_IN) | |
| L2 | TBD | Series | |
| C8 | TBD | Shunt, antenna side of L2 |
ESP32-C3 Hardware Design Guidelines v1.8 (2025-06-05): Figure 7 (ESP32-C3 Schematic for RF Matching), page 10.
Gaps in the source
- Table 2 names C11 and C12, while Figure 7 labels the two capacitors C8 and C9. The guide does not say which range belongs to which capacitor.
- Espressif prints value ranges, not one value per part.
- No design frequency is printed with the target. The harmonic limits are at 4.8 GHz and 7.2 GHz, twice and three times 2.4 GHz.
Other printed numbers
- S21 less than −35 dB at 4.8 GHz and 7.2 GHz (ESP32-C3 Hardware Design Guidelines v1.8 (2025-06-05), Schematic Checklist, RF Tuning, page 11)
- Add a stub to the first capacitor in the matching circuit at the chip end (ESP32-C3 Hardware Design Guidelines v1.8 (2025-06-05), Note under Table 2, page 11)
Sources
- ESP32-C3 Hardware Design Guidelines, v1.8, 2025-06-05, read 2026-11-12
Other chips
L-network calculatorQuestion about this chip, or a correction?