SX1262 915 MHz Matching: 2.5 nH, 5.6 pF, 4.7 nH, 1.8 pF
Semtech prints no target impedance for the SX1262 PA pin, only the parts on its reference board. On the SX1262MB1CAS 915 MHz +22 dBm module the transmit match from RFO is L3 2.5 nH with C4 3.0 pF across it, C5 5.6 pF shunt, then L4 4.7 nH and C7 1.8 pF, with L1 47 nH feeding the PA from VR_PA.
Transmit path, RFO to the RF switch
SX1262MB1CAS at 915 MHz, the +22 dBm reference design for the USA and Canada (AN1200.40 section 2.2). RFO, L2 in series, L1 from VR_PA and C3 shunt at the next node, L3 in series with C4 across it, C5 shunt, C6 in series, L4 in series, C7 shunt, then RF1 of the PE4259 switch.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| L2 | 0R | Series, at RFO | CRCW04020000Z0ED |
| L1 | 47nH | From VR_PA to the PA output node | LQW15AN47NJ00D |
| C3 | Not in the BOM | Shunt at the PA output node | |
| L3 | 2.5nH | Series | LQW15AN2N5C00D |
| C4 | 3.0pF | Across L3 (second-harmonic notch) | GJM1555C1H3R0BB01D |
| C5 | 5.6pF | Shunt | GJM1555C1H5R6CB01D |
| C6 | 39pF | Series (DC block) | GJM1555C1H390JB01D |
| L4 | 4.7nH | Series | LQW15AN4N7C00D |
| C7 | 1.8pF | Shunt, at RF1 of the switch | GJM1555C1H1R8BB01D |
SX1262MB1CAS RF Module, 4-Layers 915MHz BOM BOM V1a, SCH e428v03a (2023-09-25): BOM rows; topology from AN1200.40 Figure 5, page 9.
Receive path, RF switch to the LNA inputs
Same module and BOM. RF2 of the switch, C13 shunt, C11 in series to RFI_N, L6 from RFI_N to RFI_P, C12 shunt at RFI_P. AN1200.40 calls C11, C12 and L6 the balun.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C13 | Not in the BOM | Shunt at RF2 (optional, for interferer rejection) | |
| C11 | 2.4pF | Series to RFI_N | GJM1555C1H2R4BB01D |
| L6 | 15nH | From RFI_N to RFI_P | LQW15AN15NH00D |
| C12 | 1.8pF | Shunt at RFI_P | GJM1555C1H1R8BB01D |
SX1262MB1CAS RF Module, 4-Layers 915MHz BOM BOM V1a, SCH e428v03a (2023-09-25): BOM rows; topology from AN1200.40 Figure 5, page 9, and section 4, page 21.
Antenna side of the RF switch
Same module and BOM, into the 50 Ohms SMA. RFC of the switch, C8 in series, C9 shunt, L5 in series, C10 shunt, then the SMA.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C8 | 39pF | Series | GJM1555C1H390JB01D |
| C9 | 3.3pF | Shunt | GJM1555C1H3R3BB01D |
| L5 | 9.1nH | Series | LQW15AN9N1H00D |
| C10 | 3.3pF | Shunt, at the SMA | GJM1555C1H3R3BB01D |
SX1262MB1CAS RF Module, 4-Layers 915MHz BOM BOM V1a, SCH e428v03a (2023-09-25): BOM rows; topology from AN1200.40 Figure 15, page 17.
Gaps in the source
- Semtech prints no PA load impedance for the SX1262, so this page has no target and no Match link.
- Semtech prints one BOM for this module, the 915 MHz +22 dBm build. The datasheet's lower-power PA settings say they need a dedicated matching network and print no values for it.
- C3 and C13 are drawn on the schematic and absent from the BOM, which says parts not listed are not populated.
Other printed numbers
- For the SX1261 at 915 MHz, the load-pull optimum at the RFO pad is 11.7 + j4.8 Ω (14.6 dBm peak), with 13.5 + j7.6 Ω for lower power and higher efficiency. These are SX1261 numbers, and the note says they may not be the most up-to-date. (AN1200.40 SX1261/2 Reference Design Explanation Rev 1.1 (May 2018), Section 3.1.1 Load-Pull, page 18)
- For the SX1261 at 915 MHz, the optimal differential source impedance at the LNA inputs is 74 + j134. (AN1200.40 SX1261/2 Reference Design Explanation Rev 1.1 (May 2018), Section 4, page 21)
- PA settings for +22, +20, +17 and +14 dBm on the SX1262 (paDutyCycle, hpMax). (SX1261/2 Data Sheet (DS.SX1261-2.W.APP) Rev 2.2 (Dec 2024), Table 13-21 PA Operating Modes with Optimal Settings, page 82)
Sources
- SX1262MB1CAS RF Module, 4-Layers 915MHz BOM, BOM V1a, SCH e428v03a, 2023-09-25, read 2026-11-12
- AN1200.40 SX1261/2 Reference Design Explanation, Rev 1.1, May 2018, read 2026-11-12
- SX1261/2 Data Sheet (DS.SX1261-2.W.APP), Rev 2.2, Dec 2024, read 2026-11-12
Other chips
L-network calculatorQuestion about this chip, or a correction?