nRF52840 Antenna Match: 1 pF, 4.7 nH, 1.2 pF, 2.2 nH
Nordic prints no impedance for the nRF52840 ANT pin, only the parts of its reference match. For new aQFN73 designs it recommends the four-part match: C3 1 pF shunt at ANT, L1 4.7 nH in series, C4 1.2 pF shunt and L5 2.2 nH in series.
Four-component RF match
QIAA aQFN73, circuit configuration no. 7. Nordic recommends it for new designs: better harmonic suppression at TXPOWER of 5 dBm or above. C3 shunt at the ANT pin (returned to VSS_PA), L1 in series, C4 shunt, L5 in series to the RF output.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C3 | 1 pF | Shunt at ANT, to VSS_PA | |
| L1 | 4.7 nH | Series | |
| C4 | 1.2 pF | Shunt | |
| L5 | 2.2 nH | Series, to the RF output |
nRF52840 Product Specification, Reference circuitry v1.11 (October 2024): Circuit configuration no. 7 for QIAA aQFN73, Figure 7 (schematic revision 1.1, 12.02.2021) and Table 17.
Three-component RF match, values v1.1
QIAA aQFN73, circuit configuration no. 1. Nordic uses v1.1 in the reference schematics and recommends it for new designs. C3 shunt at the ANT pin (returned to VSS_PA), L1 in series, C4 shunt, C22 shunt at the RF output (not mounted).
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C3 | 0.8 pF | Shunt at ANT, to VSS_PA | |
| L1 | 4.7 nH | Series | |
| C4 | 0.5 pF | Shunt | |
| C22 | N.C. | Shunt at the RF output |
nRF52840 Product Specification, Reference circuitry v1.11 (October 2024): Circuit configuration no. 1 for QIAA aQFN73, Figure 1 and Table 5.
Three-component RF match, values v1.0
Same circuit. Nordic says v1.0 is still valid; v1.1 adds margin for spurious emissions in approval tests. Same parts and places as v1.1.
| Part | Value as printed | Place | Maker part |
|---|---|---|---|
| C3 | 1 pF | Shunt at ANT, to VSS_PA | |
| L1 | 3.9 nH | Series | |
| C4 | 1 pF | Shunt |
nRF52840 Product Specification, Reference circuitry v1.11 (October 2024): Circuit configuration no. 1 for QIAA aQFN73, Table 5.
Gaps in the source
- Nordic prints no impedance for the ANT pin; the pin table calls it a single-ended antenna connection and points to the reference circuitry. This page has no target and no Match link.
- No design frequency is printed with the network.
- Nordic prints tolerances and the 0402 size for these parts (NP0 capacitors, ±5% high-frequency chip inductors) and no part numbers.
Other printed numbers
- The three-component designs stay valid. Of the two three-component value sets, Nordic recommends v1.1 for new designs. (nRF52840 Product Specification, Reference circuitry v1.11 (October 2024), Reference circuitry, introduction)
Sources
- nRF52840 Product Specification, Reference circuitry, v1.11, October 2024, read 2026-11-12
Other chips
L-network calculatorQuestion about this chip, or a correction?