SUCOFLEX 104 cable loss
SUCOFLEX 104 loses 0.88 dB per 10 m at 144 MHz (extrapolated) and 3.72 dB at 2.4 GHz. The part is Huber+Suhner SUCOFLEX_104, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.
SUCOFLEX 104 loss for 10.0 m, matched
Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)
Neighbours at 2.40 GHz
- Aircell 73.42 dB
- SUCOFLEX 126E3.72 dB
- SUCOFLEX 1043.72 dB
- LMR-2404.16 dB
- Belden 82674.83 dB
Rank 7 of 24 cables with a number at 2.40 GHz, lowest loss first.
Loss chart

Loss at 144 MHz to 5.8 GHz
| Frequency | dB per 10 m | dB per 100 ft | From |
|---|---|---|---|
| 144 MHz | 0.88 | 2.68 | extrapolated |
| 433 MHz | 1.54 | 4.69 | printed |
| 915 MHz | 2.26 | 6.88 | printed |
| 1.09 GHz | 2.47 | 7.53 | printed |
| 2.4 GHz | 3.72 | 11.3 | printed |
| 5.8 GHz | 5.93 | 18.1 | printed |
Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.
Cross-section
Loss at each band
| Band | dB per 10 m | dB per 100 ft |
|---|---|---|
| 1.8 MHz | Below the usable range, which starts at 6.7 MHz | |
| 3.5 MHz | Below the usable range, which starts at 6.7 MHz | |
| 7 MHz | 0.19 | 0.59extrapolated |
| 14 MHz | 0.27 | 0.83extrapolated |
| 28 MHz | 0.39 | 1.17extrapolated |
| 50 MHz | 0.52 | 1.57extrapolated |
| 144 MHz | 0.88 | 2.68extrapolated |
| 433 MHz | 1.54 | 4.69 |
| 915 MHz | 2.26 | 6.88 |
| 1.57 GHz | 2.99 | 9.10 |
| 2.4 GHz | 3.72 | 11.3 |
| 5.8 GHz | 5.93 | 18.1 |
Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.
Datasheet table
| MHz | Printed, dB/m | Fit | Fit − printed | Maker formula |
|---|---|---|---|---|
| 200 | 0.104 | 0.1039 | -0.000 | 0.1039 |
| 400 | 0.148 | 0.1477 | -0.000 | 0.1477 |
| 600 | 0.182 | 0.1817 | -0.000 | 0.1817 |
| 800 | 0.211 | 0.2106 | -0.000 | 0.2106 |
| 1000 | 0.236 | 0.2362 | +0.000 | 0.2362 |
| 1200 | 0.259 | 0.2595 | +0.000 | 0.2595 |
| 1400 | 0.281 | 0.2810 | -0.000 | 0.2810 |
| 1600 | 0.301 | 0.3011 | +0.000 | 0.3012 |
| 1800 | 0.32 | 0.3201 | +0.000 | 0.3201 |
| 2000 | 0.338 | 0.3382 | +0.000 | 0.3382 |
| 4000 | 0.487 | 0.4866 | -0.000 | 0.4866 |
| 6000 | 0.604 | 0.6038 | -0.000 | 0.6038 |
| 8000 | 0.705 | 0.7049 | -0.000 | 0.7048 |
| 10000 | 0.795 | 0.7956 | +0.001 | 0.7955 |
| 20000 | 1.167 | 1.167 | -0.000 | 1.167 |
| 26500 | 1.368 | 1.368 | -0.000 | 1.368 |
Huber+Suhner SUCOFLEX_104 data sheet, document PIM-P716, published 27 Oct 2023, accessed 2026-10-11. Huber+Suhner SUCOFLEX_104.
α (dB/m) = a·√f + b·f with f in GHz: a = 0.2290, b = 0.007127. Least squares over the 16 printed rows. RMS miss 0.000 dB/m, largest 0.001 dB/m at 10.0 GHz.
The sheet's own formula: dB/m = 0.2291·√f + 0.0071·f with f in GHz.
Usable range and build
Printed from 200 MHz to 26.5 GHz. Usable from 6.7 MHz to 26.5 GHz; the top is set by the rated maximum.
- Maker
- Huber+Suhner
- Impedance
- 50 Ω
- Velocity factor
- 0.77
- Delay
- 4.33 ns/m
- Dielectric
- PTFE
- Centre conductor
- not printed
- Dielectric diameter
- not printed
- Jacket OD
- 5.5 mm
- Rated maximum
- 26.5 GHz
- Printed cutoff
- not printed
- Weight
- 72 g/m
- Bend radius, installed
- 16 mm
- Bend radius, repeated
- not printed
- Shield
- Silver-plated copper foil plus silver-plated copper braid
- Sold as an assembly. Jacket on this sheet is 5.5 mm FEP. The armoured SUCOFLEX_104_G jacket is a different mechanical part and is not used here. Nominal attenuation only. Rated to 26.5 GHz, the last printed row.
Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?