RG-213 cable loss (Belden 8267)

Belden 8267 loses 0.78 dB per 10 m at 144 MHz and 4.83 dB at 2.4 GHz. The part is Belden 8267, RG-213, PE, commercial non-QPL (M17/163-00001), and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

Belden 8267 loss for 10.0 m, matched

0.010.11101001 MHz10 MHz100 MHz1 GHz10 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
4.83 dB
Out of 100 W
32.9 W
Delivered
32.9%

Neighbours at 2.40 GHz

  1. SUCOFLEX 1043.72 dB
  2. LMR-2404.16 dB
  3. Belden 82674.83 dB
  4. H1554.91 dB
  5. SUCOFLEX 1025.90 dB

Rank 9 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of Belden 8267 (RG-213) against frequency, per 10 m and per 100 ft: 0.78 dB per 10 m at 144 MHz and 4.83 dB per 10 m at 2.4 GHz.
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz0.782.37printed
433 MHz1.524.62printed
915 MHz2.477.52printed
1.09 GHz2.778.46printed
2.4 GHz4.8314.7printed
5.8 GHz9.4128.7extrapolated

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 10.3 mmDielectric⌀ 7.24 mmCentre conductor⌀ 2.26 mm2 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.070.23
3.5 MHz0.100.32
7 MHz0.150.45
14 MHz0.210.65
28 MHz0.310.95
50 MHz0.431.30
144 MHz0.782.37
433 MHz1.524.62
915 MHz2.477.52
1.57 GHz3.5810.9
2.4 GHz4.8314.7
5.8 GHz9.4128.7extrapolated

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printed
10.170.1668-0.003
100.550.5466-0.003
501.31.299-0.001
1001.91.919+0.019
2002.72.878+0.178
4004.14.397+0.297
7006.56.294-0.206
9007.67.433-0.167
100087.978-0.022
400021.521.54+0.040

Belden 8267 technical data sheet, accessed 2026-10-11. Belden 8267, RG-213, PE, commercial non-QPL (M17/163-00001).

α (dB/m) = a·√f + b·f with f in GHz: a = 0.1702, b = 0.09160. Least squares over the 10 printed rows. RMS miss 0.139 dB/100 ft, largest 0.297 dB/100 ft at 400 MHz.

Usable range and build

Printed from 1 MHz to 4 GHz. Usable from 1 MHz to 13.3 GHz; the top is set by the TE11 cutoff. TE11 cutoff 13.3 GHz, from the printed diameters and velocity factor.

Maker
Belden
RG name on the sheet
RG-213
Impedance
50 Ω
Velocity factor
0.66
Delay
5.05 ns/m
Dielectric
polyethylene
Centre conductor
0.089 in (2.26 mm)
Dielectric diameter
0.285 in (7.24 mm)
Jacket OD
10.3 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
104 lb/1000 ft
Bend radius, installed
4 in (102 mm)
Bend radius, repeated
not printed
Shield
Bare copper braid, 95%
  • The printed table jumps from 1000 MHz to 4000 MHz. Frequencies between those rows are the fit, not a printed point.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?