IndieRF Mixer Spur Chart
Mixer spur calculator and chart
With RF 1500 to 1700 MHz, a 1010 MHz low-side LO and a 490 to 690 MHz IF, the 1x2 product |RF − 2LO| lands at 320 to 520 MHz, inside the IF, where no filter after the mixer can take it out. Type your RF band, IF band and LO side to see every m x n product and input spur to order 15, the image and the half-IF included, and paste the datasheet spur table to put a level on each.
Mixer spur chart
RF 1500 to 1700 MHz, LO 1010 MHz (low side), IF 490 to 690 MHz
Scroll sideways for more columns
| Product | m x n | Output (MHz) | In IF band |
|---|---|---|---|
| |RF − 2LO| | 1x2 | 320 to 520 | Yes |
| RF + LO | 1x1 | 2510 to 2710 | |
| LO | 0x1 | 1010 | |
| RF | 1x0 | 1500 to 1700 | |
| 2LO | 0x2 | 2020 | |
| 2RF | 2x0 | 3000 to 3400 | |
| 3LO | 0x3 | 3030 | |
| RF + 2LO | 1x2 | 3520 to 3720 | |
| 2RF + LO | 2x1 | 4010 to 4410 | |
| |2RF − LO| | 2x1 | 1990 to 2390 | |
| 3RF | 3x0 | 4500 to 5100 | |
| 4LO | 0x4 | 4040 | |
| RF + 3LO | 1x3 | 4530 to 4730 | |
| |RF − 3LO| | 1x3 | 1330 to 1530 | |
| 2RF + 2LO | 2x2 | 5020 to 5420 | |
| |2RF − 2LO| | 2x2 | 980 to 1380 | |
| 3RF + LO | 3x1 | 5510 to 6110 | |
| |3RF − LO| | 3x1 | 3490 to 4090 | |
| 4RF | 4x0 | 6000 to 6800 | |
| 5LO | 0x5 | 5050 | |
| RF + 4LO | 1x4 | 5540 to 5740 | |
| |RF − 4LO| | 1x4 | 2340 to 2540 | |
| 2RF + 3LO | 2x3 | 6030 to 6430 | |
| |2RF − 3LO| | 2x3 | 0 to 370 | |
| 3RF + 2LO | 3x2 | 6520 to 7120 | |
| |3RF − 2LO| | 3x2 | 2480 to 3080 | |
| 4RF + LO | 4x1 | 7010 to 7810 | |
| |4RF − LO| | 4x1 | 4990 to 5790 | |
| 5RF | 5x0 | 7500 to 8500 |
Datasheet m x n table (optional)
Paste the spur table to add a level to each row: rows are RF harmonics m = 0, 1, 2 and columns LO harmonics n = 0, 1, 2, in dBc below the IF output. Header rows, an index column and blanks (-, x) are fine. Levels are read at the table's own RF drive. If your sheet prints LO harmonics as rows, read it, then swap.
Reading the chart
Each bar is one product or one input spur, drawn across the band it covers and placed on the row of its order m + n. A product of m·RF covers m times the RF bandwidth, so the high-order bars get wide fast. In the default plan the 1x2 product |RF − 2LO| sweeps 320 to 520 MHz as the RF moves across 1500 to 1700 MHz, and the top 30 MHz of that sweep sits inside the 490 to 690 MHz IF. A red bar overlaps the shaded band: the IF on the output view, the RF band on the input view. A red output product passes the IF filter with the wanted signal. A red input spur passes the preselector with it.
The input view answers the other question: which input frequencies come out at the IF. The 1x2 spur 2LO − IF covers 1330 to 1530 MHz and overlaps the RF band, so a signal there converts to the IF and no filter ahead of the mixer can stop it. The image, LO − IF at 320 to 520 MHz, is clear of the RF band here, and the preselector has to take it out. Moving the LO to the high side moves every one of these.
Definitions
- m is the RF harmonic and n the LO harmonic. The order is m + n, and the page lists every product with order 1 to the highest you set, up to 15.
- Output products: |m·fRF + n·fLO| and |m·fRF − n·fLO|. The wanted 1x1 difference is left out; the 1x1 sum stays.
- Input spurs: f = (±n·fLO ± fIF)/m for f > 0. The 1x1 branch that is the RF band itself is left out. The other 1x1 is the image. The 2x2 on the same side of the LO as the RF band is the half-IF.
- LO: typed, or the RF centre minus the IF centre (low side) or plus it (high side). A band that crosses 0 Hz folds back, and a bar that touches the band edge counts as in band.
- Levels: a pasted datasheet table gives table[m][n] in dBc against the wanted IF, at the RF drive the table was measured at. The image reads 0 dBc. An output product of RF order m moves (m − 1) dB for each dB of RF drive, so a table taken at a stronger drive overstates the high-m products at yours.
To order 5 a plan has 29 output products and 24 input spurs. The Cascade analysis page runs the same planner on a mixer in your chain and reads each filter's rejection off its curve. The frequency plan runs in your browser and never leaves it.
Checked against an exact-fraction Python reference: the cases, the tolerance and what the check does not cover.