IndieRF Mixer Spur Chart

Mixer spur calculator and chart

With RF 1500 to 1700 MHz, a 1010 MHz low-side LO and a 490 to 690 MHz IF, the 1x2 product |RF − 2LO| lands at 320 to 520 MHz, inside the IF, where no filter after the mixer can take it out. Type your RF band, IF band and LO side to see every m x n product and input spur to order 15, the image and the half-IF included, and paste the datasheet spur table to put a level on each.

Mixer spur chart

RF 1500 to 1700 MHz, LO 1010 MHz (low side), IF 490 to 690 MHz

LO side

1 product lands in the IF, where no filter after the mixer can take it out: 1x2 |RF − 2LO| at 320 to 520 MHz.

1 input spur sits inside the RF band, past any preselector: 1x2 2LO − IF at 1330 to 1530 MHz.

Image LO − IF: 320 to 520 MHz. Half-IF (2LO + IF)/2: 1255 to 1355 MHz.

12345m+n0500100015002000MHzLOLO: 1010 to 1010 MHz2LO: 2020 to 2020 MHzRF: 1500 to 1700 MHz|RF − 3LO|: 1330 to 1530 MHz|2RF − LO|: 1990 to 2390 MHz|2RF − 2LO|: 980 to 1380 MHz|2RF − 3LO|: 0 to 370 MHz|RF − 2LO|: 320 to 520 MHz|RF − 2LO|
Output products from 0 to 2070 MHz by order m + n; the IF band is shaded. Red: overlaps the IF band. Dashed line: LO. 21 more products sit outside this window and are in the table.

Scroll sideways for more columns

Productm x nOutput (MHz)In IF band
|RF − 2LO|1x2320 to 520Yes
RF + LO1x12510 to 2710
LO0x11010
RF1x01500 to 1700
2LO0x22020
2RF2x03000 to 3400
3LO0x33030
RF + 2LO1x23520 to 3720
2RF + LO2x14010 to 4410
|2RF − LO|2x11990 to 2390
3RF3x04500 to 5100
4LO0x44040
RF + 3LO1x34530 to 4730
|RF − 3LO|1x31330 to 1530
2RF + 2LO2x25020 to 5420
|2RF − 2LO|2x2980 to 1380
3RF + LO3x15510 to 6110
|3RF − LO|3x13490 to 4090
4RF4x06000 to 6800
5LO0x55050
RF + 4LO1x45540 to 5740
|RF − 4LO|1x42340 to 2540
2RF + 3LO2x36030 to 6430
|2RF − 3LO|2x30 to 370
3RF + 2LO3x26520 to 7120
|3RF − 2LO|3x22480 to 3080
4RF + LO4x17010 to 7810
|4RF − LO|4x14990 to 5790
5RF5x07500 to 8500

Datasheet m x n table (optional)

Paste the spur table to add a level to each row: rows are RF harmonics m = 0, 1, 2 and columns LO harmonics n = 0, 1, 2, in dBc below the IF output. Header rows, an index column and blanks (-, x) are fine. Levels are read at the table's own RF drive. If your sheet prints LO harmonics as rows, read it, then swap.

Reading the chart

Each bar is one product or one input spur, drawn across the band it covers and placed on the row of its order m + n. A product of m·RF covers m times the RF bandwidth, so the high-order bars get wide fast. In the default plan the 1x2 product |RF − 2LO| sweeps 320 to 520 MHz as the RF moves across 1500 to 1700 MHz, and the top 30 MHz of that sweep sits inside the 490 to 690 MHz IF. A red bar overlaps the shaded band: the IF on the output view, the RF band on the input view. A red output product passes the IF filter with the wanted signal. A red input spur passes the preselector with it.

The input view answers the other question: which input frequencies come out at the IF. The 1x2 spur 2LO − IF covers 1330 to 1530 MHz and overlaps the RF band, so a signal there converts to the IF and no filter ahead of the mixer can stop it. The image, LO − IF at 320 to 520 MHz, is clear of the RF band here, and the preselector has to take it out. Moving the LO to the high side moves every one of these.

Definitions

  • m is the RF harmonic and n the LO harmonic. The order is m + n, and the page lists every product with order 1 to the highest you set, up to 15.
  • Output products: |m·fRF + n·fLO| and |m·fRF − n·fLO|. The wanted 1x1 difference is left out; the 1x1 sum stays.
  • Input spurs: f = (±n·fLO ± fIF)/m for f > 0. The 1x1 branch that is the RF band itself is left out. The other 1x1 is the image. The 2x2 on the same side of the LO as the RF band is the half-IF.
  • LO: typed, or the RF centre minus the IF centre (low side) or plus it (high side). A band that crosses 0 Hz folds back, and a bar that touches the band edge counts as in band.
  • Levels: a pasted datasheet table gives table[m][n] in dBc against the wanted IF, at the RF drive the table was measured at. The image reads 0 dBc. An output product of RF order m moves (m − 1) dB for each dB of RF drive, so a table taken at a stronger drive overstates the high-m products at yours.

To order 5 a plan has 29 output products and 24 input spurs. The Cascade analysis page runs the same planner on a mixer in your chain and reads each filter's rejection off its curve. The frequency plan runs in your browser and never leaves it.

Checked against an exact-fraction Python reference: the cases, the tolerance and what the check does not cover.

Question or a correction?