PCBWay 4-layer 0.8 mm 50% stackup: layers, εr, 50 Ω and 90 Ω widths
PCBWay 4-layer 0.8 mm 50% is PCBWay's 0.8 mm 4-layer structure for 50% inner residual copper: 0.1785 mm of 7628 prepreg, RC46% at εr 4.74 under layer 1, over a 0.230 mm core. A 50 Ω microstrip on layer 1 is 11.59 mil (0.294 mm) with no solder mask, because PCBWay does not print one, at 1 GHz.
Open PCBWay 4-layer 0.8 mm 50% in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | Not printed | Not printed | |
| L1 | Copper | 0.0350 mm | 1 oz finished | |
| L1 to L2 | 7628 prepreg, RC46% | 0.1785 mm | 4.74 | |
| L2 | Copper | 0.0350 mm | 1 oz | |
| L2 to L3 | core | 0.230 mm | 4.6 | |
| L3 | Copper | 0.0350 mm | 1 oz | |
| L3 to L4 | 7628 prepreg, RC46% | 0.1785 mm | 4.74 | |
| L4 | Copper | 0.0350 mm | 1 oz finished | |
| Mask | Solder mask | Not printed | Not printed |
After lamination the 7628 between layer 1 and layer 2 is 0.1785 mm on the 50% residual-copper row. The glass before press is 0.1960 mm. This is the 50% inner residual-copper row. PCBWay prints 70%, 50% and 30% rows and says to use the 70% row above 60% and the 30% row at 40% or less. PCBWay does not state the frequency for this DK.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, mask off | 11.59 mil (0.294 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, mask off | 8.44 mil (0.214 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, mask off | 6.41 mil (0.163 mm) | 100.00 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with no solder mask. PCBWay does not print a mask thickness or εr, and its own impedance calculator leaves the mask out, so these widths are mask off. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that.
What PCBWay does not print
No typical number fills these, and none of them sets a width on this page.
- Solder mask thickness. The tolerances page names the mask as LPI and gives no thickness.
- Solder mask εr. PCBWay's impedance calculator leaves the mask out of outer-layer checks, so the widths here are mask off.
- The frequency of each DK. The table prints DK with no frequency.
- Loss tangent (Df). The table prints none, so loss uses this calculator's 0.02 and the widths do not depend on it.
The same 50 Ω line on the other PCBWay 4-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- PCBWay 4-layer 1.6 mm 70%: 12.08 mil (0.307 mm) over 0.1855 mm
- PCBWay 4-layer 1.6 mm 50%: 11.59 mil (0.294 mm) over 0.1785 mm
- PCBWay 4-layer 1.6 mm 30%: 11.11 mil (0.282 mm) over 0.1715 mm
- PCBWay 4-layer 1.2 mm 70%: 12.08 mil (0.307 mm) over 0.1855 mm
- PCBWay 4-layer 1.2 mm 50%: 11.59 mil (0.294 mm) over 0.1785 mm
- PCBWay 4-layer 1.2 mm 30%: 11.11 mil (0.282 mm) over 0.1715 mm
- PCBWay 4-layer 1.0 mm 70%: 12.08 mil (0.307 mm) over 0.1855 mm
- PCBWay 4-layer 1.0 mm 50%: 11.59 mil (0.294 mm) over 0.1785 mm
- PCBWay 4-layer 1.0 mm 30%: 11.11 mil (0.282 mm) over 0.1715 mm
- PCBWay 4-layer 0.8 mm 70%: 12.08 mil (0.307 mm) over 0.1855 mm
- PCBWay 4-layer 0.8 mm 50%: 11.59 mil (0.294 mm) over 0.1785 mm
- PCBWay 4-layer 0.8 mm 30%: 11.11 mil (0.282 mm) over 0.1715 mm
Sources
- PCBWay multilayer stackup, read 2026-11-15
- PCBWay manufacturing tolerances, read 2026-11-15
- PCBWay impedance calculator, read 2026-11-15
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?