RG-58 cable loss (Belden 8262)

Belden 8262 loses 1.99 dB per 10 m at 144 MHz and 13.5 dB at 2.4 GHz (extrapolated). The part is Belden 8262, RG-58, commercial non-QPL (M17/155-00001), and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

Belden 8262 loss for 10.0 m, matched

0.10.31310301001 MHz10 MHz100 MHz1 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
13.48 dB
Out of 100 W
4.49 W
Delivered
4.5%

Extrapolated. Extrapolated 2.4× past the last printed row at 1 GHz.

Neighbours at 2.40 GHz

  1. Hand-Flex 08611.42 dB
  2. LMR-100A12.76 dB
  3. Belden 826213.48 dB, extrapolated
  4. Taoglas RG-31614.61 dB
  5. Belden 8328415.50 dB

Rank 20 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of Belden 8262 (RG-58) against frequency, per 10 m and per 100 ft: 1.99 dB per 10 m at 144 MHz and 13.5 dB per 10 m at 2.4 GHz (extrapolated).
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz1.996.07printed
433 MHz3.9912.2printed
915 MHz6.6520.3printed
1.09 GHz7.5222.9extrapolated
2.4 GHz13.541.1extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 4.95 mmDielectric⌀ 2.92 mmCentre conductor⌀ 0.889 mm2 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.180.55
3.5 MHz0.250.77
7 MHz0.371.11
14 MHz0.531.61
28 MHz0.772.35
50 MHz1.073.26
144 MHz1.996.07
433 MHz3.9912.2
915 MHz6.6520.3
1.57 GHz9.8329.9extrapolated
2.4 GHz13.541.1extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printed
10.40.4064+0.006
101.41.347-0.053
503.33.260-0.040
1004.94.874-0.026
2007.37.420+0.120
40011.511.55+0.049
7001716.82-0.184
9002020.02+0.024
100021.521.57+0.069

Belden 8262 technical data sheet, accessed 2026-10-11. Belden 8262, RG-58, commercial non-QPL (M17/155-00001).

α (dB/m) = a·√f + b·f with f in GHz: a = 0.4123, b = 0.2953. Least squares over the 9 printed rows. RMS miss 0.083 dB/100 ft, largest 0.184 dB/100 ft at 700 MHz.

Usable range and build

Printed from 1 MHz to 1 GHz. Usable from 1 MHz to 4 GHz; the top is set by the 4× the last printed row. TE11 cutoff 33.1 GHz, from the printed diameters and velocity factor.

Maker
Belden
RG name on the sheet
RG-58
Impedance
50 Ω
Velocity factor
0.66
Delay
5.05 ns/m
Dielectric
polyethylene
Centre conductor
0.035 in (0.889 mm)
Dielectric diameter
0.115 in (2.92 mm)
Jacket OD
4.95 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
24 lb/1000 ft
Bend radius, installed
2 in (50.8 mm)
Bend radius, repeated
not printed
Shield
Tinned copper braid, 95%
  • Attenuation is printed through 1000 MHz. The sheet prints no maximum operating frequency.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?