RG-316 cable loss (Taoglas)
Taoglas RG-316 loses 3.05 dB per 10 m at 144 MHz (extrapolated) and 14.6 dB at 2.4 GHz. The part is Taoglas 301615A000096A, 2.5 mm RG-316, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.
Taoglas RG-316 loss for 10.0 m, matched
Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)
Neighbours at 2.40 GHz
- LMR-100A12.76 dB
- Belden 826213.48 dB, extrapolated
- Taoglas RG-31614.61 dB
- Belden 8328415.50 dB
- Belden 821619.76 dB, extrapolated
Rank 21 of 24 cables with a number at 2.40 GHz, lowest loss first.
Loss chart

Loss at 144 MHz to 5.8 GHz
| Frequency | dB per 10 m | dB per 100 ft | From |
|---|---|---|---|
| 144 MHz | 3.05 | 9.28 | extrapolated |
| 433 MHz | 5.50 | 16.8 | printed |
| 915 MHz | 8.34 | 25.4 | printed |
| 1.09 GHz | 9.21 | 28.1 | printed |
| 2.4 GHz | 14.6 | 44.5 | printed |
| 5.8 GHz | 25.2 | 76.8 | printed |
Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.
Cross-section
Loss at each band
| Band | dB per 10 m | dB per 100 ft |
|---|---|---|
| 1.8 MHz | Below the usable range, which starts at 6.7 MHz | |
| 3.5 MHz | Below the usable range, which starts at 6.7 MHz | |
| 7 MHz | 0.64 | 1.96extrapolated |
| 14 MHz | 0.91 | 2.78extrapolated |
| 28 MHz | 1.30 | 3.96extrapolated |
| 50 MHz | 1.75 | 5.34extrapolated |
| 144 MHz | 3.05 | 9.28extrapolated |
| 433 MHz | 5.50 | 16.8 |
| 915 MHz | 8.34 | 25.4 |
| 1.57 GHz | 11.4 | 34.7 |
| 2.4 GHz | 14.6 | 44.5 |
| 5.8 GHz | 25.2 | 76.8 |
Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.
Datasheet table
| MHz | Printed, dB/m | Fit | Fit − printed |
|---|---|---|---|
| 200 | 0.37 | 0.3626 | -0.007 |
| 400 | 0.551 | 0.5268 | -0.024 |
| 900 | 0.855 | 0.8262 | -0.029 |
| 1500 | 1.111 | 1.107 | -0.004 |
| 2000 | 1.32 | 1.311 | -0.009 |
| 2500 | 1.48 | 1.497 | +0.017 |
| 3000 | 1.577 | 1.671 | +0.094 |
| 4000 | 2.05 | 1.994 | -0.056 |
| 5000 | 2.28 | 2.292 | +0.012 |
| 6000 | 2.59 | 2.574 | -0.016 |
Taoglas RG-316 cable specification SPE-23-8-107-C, accessed 2026-10-11. Taoglas 301615A000096A, 2.5 mm RG-316.
α (dB/m) = a·√f + b·f with f in GHz: a = 0.7572, b = 0.1198. Least squares over the 10 printed rows. RMS miss 0.038 dB/m, largest 0.094 dB/m at 3.00 GHz.
Usable range and build
Printed from 200 MHz to 6 GHz. Usable from 6.7 MHz to 6 GHz; the top is set by the end of the printed table.
- Maker
- Taoglas
- RG name on the sheet
- RG-316
- Impedance
- 50 Ω
- Velocity factor
- not printed
- Dielectric
- PTFE
- Centre conductor
- not printed
- Dielectric diameter
- 1.52 mm
- Jacket OD
- 2.5 mm
- Rated maximum
- not printed
- Printed cutoff
- not printed
- Weight
- not printed
- Bend radius, installed
- 50 mm
- Bend radius, repeated
- not printed
- Shield
- Silver-coated copper braid, 96%
- Velocity factor is not printed, so delay and phase are omitted and the cutoff cannot be computed. Loss stops at the 6000 MHz row. Impedance is 50 ± 3 Ω and capacitance is 100 ± 5 pF/m. This is not the Belden 83284 table.
- The sheet prints 0.125 kg/m, about eight times the Belden RG-316 figure, so weight is left blank. The 50 mm bend radius is not marked static or repeated.
Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?