LMR-100A cable loss

LMR-100A loses 2.87 dB per 10 m at 144 MHz and 12.8 dB at 2.4 GHz. The part is Times Microwave LMR-100A, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

LMR-100A loss for 10.0 m, matched

0.10.31310301001 MHz10 MHz100 MHz1 GHz10 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
12.76 dB
Out of 100 W
5.29 W
Delivered
5.3%

Neighbours at 2.40 GHz

  1. EZ 8610.02 dB
  2. Hand-Flex 08611.42 dB
  3. LMR-100A12.76 dB
  4. Belden 826213.48 dB, extrapolated
  5. Taoglas RG-31614.61 dB

Rank 19 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of LMR-100A against frequency, per 10 m and per 100 ft: 2.87 dB per 10 m at 144 MHz and 12.8 dB per 10 m at 2.4 GHz.
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz2.878.76printed
433 MHz5.0915.5printed
915 MHz7.5623.0printed
1.09 GHz8.3025.3printed
2.4 GHz12.838.9printed
5.8 GHz21.064.1printed

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 2.79 mmDielectric⌀ 1.52 mmCentre conductor⌀ 0.457 mm1 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.310.95extrapolated
3.5 MHz0.441.33extrapolated
7 MHz0.621.89extrapolated
14 MHz0.882.68extrapolated
28 MHz1.253.80extrapolated
50 MHz1.675.10
144 MHz2.878.76
433 MHz5.0915.5
915 MHz7.5623.0
1.57 GHz10.130.9
2.4 GHz12.838.9
5.8 GHz21.064.1

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printedMaker formula
303.93.935+0.0353.936
505.15.099-0.0015.101
1508.98.942+0.0428.946
22010.910.90-0.00310.90
45015.815.82+0.02015.83
90022.822.83+0.03122.84
150030.130.06-0.03730.07
180033.233.21+0.00633.22
200035.235.18-0.01935.19
250039.839.79-0.00739.81
580064.164.08-0.02264.10
800077.377.32+0.02377.35

Times Microwave LMR-100A flexible low loss communications coax, accessed 2026-10-11. Times Microwave LMR-100A.

α (dB/m) = a·√f + b·f with f in GHz: a = 0.7354, b = 0.05710. Least squares over the 12 printed rows. RMS miss 0.025 dB/100 ft, largest 0.042 dB/100 ft at 150 MHz.

The sheet's own formula: dB/100 ft = 0.70914·√f + 0.00174·f with f in MHz.

Usable range and build

Printed from 30 MHz to 8 GHz. Usable from 1 MHz to 32 GHz; the top is set by the 4× the last printed row. TE11 cutoff 63.6 GHz, from the printed diameters and velocity factor.

Maker
Times Microwave Systems
Impedance
50 Ω
Velocity factor
0.66
Delay
5.05 ns/m
Dielectric
solid polyethylene
Centre conductor
0.018 in (0.457 mm)
Dielectric diameter
0.06 in (1.52 mm)
Jacket OD
2.79 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
0.0092 lb/ft
Bend radius, installed
0.25 in (6.35 mm)
Bend radius, repeated
1 in (25.4 mm)
Shield
Aluminum tape plus tinned copper braid
  • The sheet prints no maximum operating frequency. The last column header is printed 80000, a typo for the 8000 MHz row. The formula on the sheet is (0.709140)·√(f_MHz) + (0.001740)·f_MHz in dB/100 ft.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?