H155 cable loss

H155 loses 1.03 dB per 10 m at 144 MHz and 4.91 dB at 2.4 GHz. The part is SSB-Electronic H155 SSB, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

H155 loss for 10.0 m, matched

0.010.030.10.313101 MHz10 MHz100 MHz1 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
4.91 dB
Out of 100 W
32.3 W
Delivered
32.3%

Neighbours at 2.40 GHz

  1. LMR-2404.16 dB
  2. Belden 82674.83 dB
  3. H1554.91 dB
  4. SUCOFLEX 1025.90 dB
  5. SR 1415.99 dB

Rank 10 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of H155 against frequency, per 10 m and per 100 ft: 1.03 dB per 10 m at 144 MHz and 4.91 dB per 10 m at 2.4 GHz.
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz1.033.13printed
433 MHz1.855.65printed
915 MHz2.818.56printed
1.09 GHz3.109.45printed
2.4 GHz4.9115.0printed
5.8 GHz8.4525.8printed

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 5.4 mmDielectric⌀ 3.9 mmCentre conductor⌀ 1.42 mm2 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.110.33extrapolated
3.5 MHz0.150.47extrapolated
7 MHz0.220.66extrapolated
14 MHz0.310.94
28 MHz0.441.34
50 MHz0.591.80
144 MHz1.033.13
433 MHz1.855.65
915 MHz2.818.56
1.57 GHz3.8311.7
2.4 GHz4.9115.0
5.8 GHz8.4525.8

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 mFitFit − printed
103.22.595-0.605
204.43.694-0.706
506.95.913-0.987
1009.18.478-0.622
14410.5510.27-0.281
20012.412.22-0.178
23013.413.17-0.232
30015.315.19-0.113
4001817.75-0.251
43218.718.51-0.190
5002020.05+0.053
80026.126.03-0.071
100029.629.52-0.080
129633.934.23+0.330
150036.837.25+0.445
175040.340.74+0.444
180040.941.42+0.521
200043.744.07+0.369
240049.149.10+0.004
300056.356.15-0.145
360062.962.76-0.142
40006766.97-0.034
480075.175.01-0.085
500077.176.96-0.138
540080.880.79-0.011
600086.586.38-0.121

SSB-Electronic H155 SSB data sheet, accessed 2026-10-25. SSB-Electronic H155 SSB.

α (dB/m) = a·√f + b·f with f in GHz: a = 0.2556, b = 0.03963. Least squares over the 26 printed rows. RMS miss 0.368 dB/100 m, largest 0.987 dB/100 m at 50.0 MHz.

Usable range and build

Printed from 10 MHz to 6 GHz. Usable from 1 MHz to 6 GHz; the top is set by the rated maximum. TE11 cutoff 28.7 GHz, from the printed diameters and velocity factor.

Maker
SSB-Electronic
Impedance
50 Ω
Velocity factor
0.8
Delay
4.17 ns/m
Dielectric
foam polyethylene
Centre conductor
1.42 mm
Dielectric diameter
3.9 mm
Jacket OD
5.4 mm
Rated maximum
6.00 GHz
Printed cutoff
not printed
Weight
41 kg/km
Bend radius, installed
27 mm
Bend radius, repeated
54 mm
Shield
Aluminum foil plus 75% tinned copper braid
  • H155 is a family name several makers use. This is SSB's version, impedance 50 ± 4 Ω. Typical attenuation at 20°C. Bend radius is printed as 5× (single) and 10× (repeated) the 5.4 mm diameter. The 10 to 50 MHz rows sit 8 to 13% below the fit. The sheet prints no date or revision.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?