RG-142 cable loss (Belden 84142)

Belden 84142 loses 1.54 dB per 10 m at 144 MHz and 7.00 dB at 2.4 GHz. The part is Belden 84142, RG-142, double silvered copper braid, FEP, commercial non-QPL (M17/60-RG142), and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

Belden 84142 loss for 10.0 m, matched

0.010.11101001 MHz10 MHz100 MHz1 GHz10 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
7.00 dB
Out of 100 W
20.0 W
Delivered
20.0%

Neighbours at 2.40 GHz

  1. LMR-1956.10 dB
  2. Belden 92586.36 dB, extrapolated
  3. Belden 841427.00 dB
  4. Harbour RG-4007.75 dB
  5. EZ 8610.02 dB

Rank 15 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of Belden 84142 (RG-142) against frequency, per 10 m and per 100 ft: 1.54 dB per 10 m at 144 MHz and 7.00 dB per 10 m at 2.4 GHz.
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz1.544.69printed
433 MHz2.748.35printed
915 MHz4.1012.5printed
1.09 GHz4.5113.7printed
2.4 GHz7.0021.3printed
5.8 GHz11.735.6printed

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 4.95 mmDielectric⌀ 2.95 mmCentre conductor⌀ 0.94 mm2 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.170.51
3.5 MHz0.230.71
7 MHz0.331.00
14 MHz0.471.43
28 MHz0.662.03
50 MHz0.892.72
144 MHz1.544.69
433 MHz2.748.35
915 MHz4.1012.5
1.57 GHz5.5216.8
2.4 GHz7.0021.3
5.8 GHz11.735.6

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printed
10.30.3777+0.078
101.11.203+0.103
502.72.722+0.022
1003.93.885-0.015
2005.65.565-0.035
4006.98.010+1.110
7001110.80-0.199
90012.512.37-0.125
100013.513.11-0.395
200019.319.24-0.064
300024.324.22-0.082
500032.632.62+0.016
800043.243.26+0.063

Belden 84142 technical data sheet, revision 0.512, accessed 2026-10-25. Belden 84142, RG-142, double silvered copper braid, FEP, commercial non-QPL (M17/60-RG142).

α (dB/m) = a·√f + b·f with f in GHz: a = 0.3907, b = 0.03930. Least squares over the 13 printed rows. RMS miss 0.337 dB/100 ft, largest 1.110 dB/100 ft at 400 MHz.

Usable range and build

Printed from 1 MHz to 8 GHz. Usable from 1 MHz to 32 GHz; the top is set by the 4× the last printed row. TE11 cutoff 34.4 GHz, from the printed diameters and velocity factor.

Maker
Belden
RG name on the sheet
RG-142
Impedance
50 Ω
Velocity factor
0.7
Delay
4.77 ns/m
Dielectric
PTFE
Centre conductor
0.037 in (0.94 mm)
Dielectric diameter
0.116 in (2.95 mm)
Jacket OD
4.95 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
42 lb/1000 ft
Bend radius, installed
2 in (50.8 mm)
Bend radius, repeated
not printed
Shield
Two silvered copper braids, 95% each
  • The 400 MHz row prints 6.9 dB/100 ft, about 10% below a smooth line through 200 and 700 MHz. It is kept as printed and the fit absorbs it. The sheet prints no maximum operating frequency or table temperature. VSWR is specified from 1 MHz to 12.4 GHz.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?