RG-8X cable loss (Belden 9258)

Belden 9258 loses 1.23 dB per 10 m at 144 MHz and 6.36 dB at 2.4 GHz (extrapolated). The part is Belden 9258, RG-8X, 16 AWG bare copper, PE, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

Belden 9258 loss for 10.0 m, matched

0.010.030.10.313101 MHz10 MHz100 MHz1 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
6.36 dB
Out of 100 W
23.1 W
Delivered
23.1%

Extrapolated. Extrapolated 2.4× past the last printed row at 1 GHz.

Neighbours at 2.40 GHz

  1. SR 1415.99 dB
  2. LMR-1956.10 dB
  3. Belden 92586.36 dB, extrapolated
  4. Belden 841427.00 dB
  5. Harbour RG-4007.75 dB

Rank 14 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of Belden 9258 (RG-8X) against frequency, per 10 m and per 100 ft: 1.23 dB per 10 m at 144 MHz and 6.36 dB per 10 m at 2.4 GHz (extrapolated).
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz1.233.75printed
433 MHz2.276.91printed
915 MHz3.5110.7printed
1.09 GHz3.9011.9extrapolated
2.4 GHz6.3619.4extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Jacket OD⌀ 6.15 mmDielectric⌀ 3.94 mmCentre conductor⌀ 1.45 mm2 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHz0.130.39
3.5 MHz0.180.54
7 MHz0.250.77
14 MHz0.361.10
28 MHz0.521.57
50 MHz0.702.13
144 MHz1.233.75
433 MHz2.276.91
915 MHz3.5110.7
1.57 GHz4.8814.9extrapolated
2.4 GHz6.3619.4extrapolated
5.8 GHzPast 4 GHz, 4× the last printed row

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/100 ftFitFit − printed
10.30.2876-0.012
100.90.9250+0.025
502.12.131+0.031
1003.13.079-0.021
2004.54.487-0.013
4006.66.609+0.009
7009.19.128+0.028
90010.710.59-0.110
100011.211.28+0.079

Belden 9258 technical data sheet, accessed 2026-10-11. Belden 9258, RG-8X, 16 AWG bare copper, PE.

α (dB/m) = a·√f + b·f with f in GHz: a = 0.2961, b = 0.07396. Least squares over the 9 printed rows. RMS miss 0.049 dB/100 ft, largest 0.110 dB/100 ft at 900 MHz.

Usable range and build

Printed from 1 MHz to 1 GHz. Usable from 1 MHz to 4 GHz; the top is set by the 4× the last printed row. TE11 cutoff 29.1 GHz, from the printed diameters and velocity factor.

Maker
Belden
RG name on the sheet
RG-8X
Impedance
50 Ω
Velocity factor
0.82
Delay
4.07 ns/m
Dielectric
polyethylene
Centre conductor
0.057 in (1.45 mm)
Dielectric diameter
0.155 in (3.94 mm)
Jacket OD
6.15 mm
Rated maximum
not printed
Printed cutoff
not printed
Weight
37 lb/1000 ft
Bend radius, installed
2.4 in (61 mm)
Bend radius, repeated
not printed
Shield
Bare copper braid, 95%
  • The sheet titles the family RG-8 and the description RG-8X. The jacket is 0.242 in, which is the RG-8X size. Attenuation is printed through 1000 MHz.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?