RG-402 cable loss (SR 141)

SR 141 loses 1.29 dB per 10 m at 144 MHz (extrapolated) and 5.99 dB at 2.4 GHz. The part is Huber+Suhner SR_141_TP_M17, and every number here is fitted to the attenuation table on its datasheet. Drag the cursor or type a frequency, length and power to read the loss for your run.

SR 141 loss for 10.0 m, matched

0.10.313103010010 MHz100 MHz1 GHz10 GHzdB for 10.0 m2.40 GHz

Fit inside the printed tableExtrapolatedDatasheet rowsBand marks (the cursor snaps to them)

10.0 m at 2.40 GHz

Lost
5.99 dB
Out of 100 W
25.1 W
Delivered
25.1%

Neighbours at 2.40 GHz

  1. H1554.91 dB
  2. SUCOFLEX 1025.90 dB
  3. SR 1415.99 dB
  4. LMR-1956.10 dB
  5. Belden 92586.36 dB, extrapolated

Rank 12 of 24 cables with a number at 2.40 GHz, lowest loss first.

Loss chart

Loss of SR 141 (RG-402) against frequency, per 10 m and per 100 ft: 1.29 dB per 10 m at 144 MHz (extrapolated) and 5.99 dB per 10 m at 2.4 GHz.
Matched loss from the fit, dB per 10 m on the left axis and per 100 ft on the right. Dots are the datasheet rows. The dashed part is past the printed table. The line stops at the usable limits.

Loss at 144 MHz to 5.8 GHz

FrequencydB per 10 mdB per 100 ftFrom
144 MHz1.293.94extrapolated
433 MHz2.317.05printed
915 MHz3.4810.6printed
1.09 GHz3.8311.7printed
2.4 GHz5.9918.3printed
5.8 GHz10.130.9printed

Printed means inside the datasheet table. A frequency outside the usable range names the limit instead of a number.

Cross-section

Outer conductor⌀ 3.58 mmDielectric⌀ 2.99 mmCentre conductor⌀ 0.92 mm1 mm
Drawn to scale from the printed diameters. The shield and jacket layers between the dielectric and the OD are not printed separately, so they share one ring.

Loss at each band

BanddB per 10 mdB per 100 ft
1.8 MHzBelow the usable range, which starts at 6.7 MHz
3.5 MHzBelow the usable range, which starts at 6.7 MHz
7 MHz0.280.84extrapolated
14 MHz0.391.19extrapolated
28 MHz0.561.69extrapolated
50 MHz0.752.28extrapolated
144 MHz1.293.94extrapolated
433 MHz2.317.05
915 MHz3.4810.6
1.57 GHz4.7114.4
2.4 GHz5.9918.3
5.8 GHz10.130.9

Matched loss from the fit. A band past the printed table is marked extrapolated. A band outside the usable range names the limit instead of a number.

Datasheet table

MHzPrinted, dB/mFitFit − printedMaker formula
2000.1530.1535+0.0010.1535
4000.2220.2217-0.0000.2217
6000.2760.2759-0.0000.2759
8000.3230.3229-0.0000.3228
10000.3650.3652+0.0000.3651
12000.4040.4042+0.0000.4041
14000.4410.4407-0.0000.4406
16000.4750.4752+0.0000.4751
18000.5080.5081+0.0000.5080
20000.540.5397-0.0000.5396
40000.810.8097-0.0000.8096
60001.0351.035+0.0001.035
80001.2381.238+0.0001.238
100001.4261.426+0.0001.426
200002.2492.249+0.0002.249
330003.1793.179-0.0003.179

Huber+Suhner SR_141_TP_M17 data sheet, document PIM-P31281, published 4 Apr 2025, accessed 2026-10-11. Huber+Suhner SR_141_TP_M17.

α (dB/m) = a·√f + b·f with f in GHz: a = 0.3255, b = 0.03967. Least squares over the 16 printed rows. RMS miss 0.000 dB/m, largest 0.001 dB/m at 200 MHz.

The sheet's own formula: dB/m = 0.32544·√f + 0.03967·f with f in GHz.

Usable range and build

Printed from 200 MHz to 33 GHz. Usable from 6.7 MHz to 33 GHz; the top is set by the rated maximum. TE11 cutoff 33.9 GHz, from the printed diameters and velocity factor.

Maker
Huber+Suhner
RG name on the sheet
RG-402
Impedance
50 Ω
Velocity factor
0.695
Delay
4.80 ns/m
Dielectric
PTFE
Centre conductor
0.92 mm
Dielectric diameter
2.99 mm
Outer conductor
3.58 mm
Rated maximum
33.0 GHz
Printed cutoff
not printed
Weight
52.1 g/m
Bend radius, installed
6.35 mm
Bend radius, repeated
not printed
Shield
Solid tin-plated copper tube
  • RG-402 is the 0.141 in (3.58 mm) semi-rigid size this cable is built to. The sheet's own name is SR_141_TP_M17, not a MIL RG-402 callout.

Compare all cablesEvery cable's fit as CSV (CC BY 4.0)Question about this cable, or a correction?