JLC04161H-2116E stackup: layers, εr, 50 Ω and 90 Ω widths
JLC04161H-2116E is JLCPCB's 1.6 mm 4-layer build: 0.2404 mm of 2116 prepreg in two plies at εr 4.16 under layer 1, over a 0.865 mm core. A 50 Ω microstrip on layer 1 is 16.78 mil (0.426 mm) with the solder mask at 1 GHz.
Open JLC04161H-2116E in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | 0.6 mil | 3.8 | |
| L1 | Copper | 1.6 mil | 1 oz finished | |
| L1 to L2 | 2116 prepreg | 0.124 + 0.1164 mm (0.2404 mm) | 4.16 | |
| L2 | Copper | 0.0152 mm | 0.5 oz | |
| L2 to L3 | core | 0.865 mm | 4.6 | |
| L3 | Copper | 0.0152 mm | 0.5 oz | |
| L3 to L4 | 2116 prepreg | 0.124 + 0.1164 mm (0.2404 mm) | 4.16 | |
| L4 | Copper | 1.6 mil | 1 oz finished | |
| Mask | Solder mask | 0.6 mil | 3.8 |
Two 2116 plies on the stackup drawing: 0.124 mm, 0.1164 mm. JLCPCB gives no pressed thickness for this build, so the height is their sum, 0.2404 mm. An older JLCPCB impedance page still lists 2116 as 4.25. This preset uses 4.16 from the current stackup page and the capabilities table. JLCPCB does not state the frequency for this εr.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, with mask | 16.78 mil (0.426 mm) | 50.00 Ω | Open |
| 50 Ω microstrip, mask off | 17.49 mil (0.444 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, with mask | 9.51 mil (0.241 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, with mask | 6.77 mil (0.172 mm) | 100.01 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that. JLCPCB's guide says the etched top width is the base width minus 0.7 mil. These widths do not subtract it, so let the coupon decide the last ohm.
The same 50 Ω line on the other 1.6 mm 4-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- JLC04161H-7628: 11.66 mil (0.296 mm) over 7.1 mil
- JLC04161H-3313: 5.42 mil (0.138 mm) over 3.5 mil
- JLC04161H-2116: 7.39 mil (0.188 mm) over 0.1164 mm
- JLC04161H-1080: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC04161H-3313A: 14.34 mil (0.364 mm) over 0.2064 mm
- JLC04161H-1080A: 11.23 mil (0.285 mm) over 0.1604 mm
- JLC04161H-1080B: 17.92 mil (0.455 mm) over 0.2444 mm
- JLC04161H-7628E: 29.94 mil (0.761 mm) over 0.4284 mm
- JLC04161H-7628F: 46.14 mil (1.172 mm) over 0.6464 mm
- JLC04161H-7628C: 46.14 mil (1.172 mm) over 0.6464 mm
- JLC04161H-2116E: 16.78 mil (0.426 mm) over 0.2404 mm
Sources
- JLCPCB impedance stackup, read 2026-11-12
- JLCPCB impedance parameters, read 2026-11-12
- JLCPCB impedance calculator guide, updated 2026-11-10, read 2026-11-12
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?