JLC04161H-3313 stackup: layers, εr, 50 Ω and 90 Ω widths
JLC04161H-3313 is JLCPCB's 1.6 mm 4-layer build: 3.5 mil of 3313 prepreg at εr 4.1 under layer 1, over a 1.265 mm core. A 50 Ω microstrip on layer 1 is 5.42 mil (0.138 mm) with the solder mask at 1 GHz.
Open JLC04161H-3313 in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | 0.6 mil | 3.8 | |
| L1 | Copper | 1.6 mil | 1 oz finished | |
| L1 to L2 | 3313 prepreg | 3.5 mil | 4.1 | |
| L2 | Copper | 0.0152 mm | 0.5 oz | |
| L2 to L3 | core | 1.265 mm | 4.6 | |
| L3 | Copper | 0.0152 mm | 0.5 oz | |
| L3 to L4 | 3313 prepreg | 3.5 mil | 4.1 | |
| L4 | Copper | 1.6 mil | 1 oz finished | |
| Mask | Solder mask | 0.6 mil | 3.8 |
JLCPCB says to use 3.5 mil for an outer-layer controlled-impedance track. The stackup drawing lists 0.0994 mm. JLCPCB says to use 4.5 mil for this 3313 when the track is inside. The drawing lists 0.0994 mm. An older JLCPCB impedance page still lists 3313 as 4.05. This preset uses 4.1 from the current stackup page and the capabilities table. JLCPCB does not state the frequency for this εr.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, with mask | 5.42 mil (0.138 mm) | 50.00 Ω | Open |
| 50 Ω microstrip, mask off | 6.00 mil (0.152 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, with mask | 4.58 mil (0.116 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, with mask | 3.42 mil (0.087 mm)under JLCPCB's 3.5 mil minimum | 100.00 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that. JLCPCB's guide says the etched top width is the base width minus 0.7 mil. These widths do not subtract it, so let the coupon decide the last ohm. JLCPCB's impedance page prints 3.5 mil as the minimum trace width and spacing (read 2026-11-12). A flagged row is under it.
The same 50 Ω line on the other 1.6 mm 4-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- JLC04161H-7628: 11.66 mil (0.296 mm) over 7.1 mil
- JLC04161H-3313: 5.42 mil (0.138 mm) over 3.5 mil
- JLC04161H-2116: 7.39 mil (0.188 mm) over 0.1164 mm
- JLC04161H-1080: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC04161H-3313A: 14.34 mil (0.364 mm) over 0.2064 mm
- JLC04161H-1080A: 11.23 mil (0.285 mm) over 0.1604 mm
- JLC04161H-1080B: 17.92 mil (0.455 mm) over 0.2444 mm
- JLC04161H-7628E: 29.94 mil (0.761 mm) over 0.4284 mm
- JLC04161H-7628F: 46.14 mil (1.172 mm) over 0.6464 mm
- JLC04161H-7628C: 46.14 mil (1.172 mm) over 0.6464 mm
- JLC04161H-2116E: 16.78 mil (0.426 mm) over 0.2404 mm
Sources
- JLCPCB impedance stackup, read 2026-11-12
- JLCPCB impedance parameters, read 2026-11-12
- JLCPCB impedance calculator guide, updated 2026-11-10, read 2026-11-12
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?