JLC06161H-2116C stackup: layers, εr, 50 Ω and 90 Ω widths
JLC06161H-2116C is JLCPCB's 1.6 mm 6-layer build: 0.2464 mm of 2116 prepreg in two plies at εr 4.16 under layer 1, over a 0.3 mm core. A 50 Ω microstrip on layer 1 is 17.24 mil (0.438 mm) with the solder mask at 1 GHz.
Open JLC06161H-2116C in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | 0.6 mil | 3.8 | |
| L1 | Copper | 1.6 mil | 1 oz finished | |
| L1 to L2 | 2116 prepreg | 0.127 + 0.1194 mm (0.2464 mm) | 4.16 | |
| L2 | Copper | 0.0152 mm | 0.5 oz | |
| L2 to L3 | core | 0.3 mm | 4.6 | |
| L3 | Copper | 0.0152 mm | 0.5 oz | |
| L3 to L4 | 2116 prepreg | 0.1194 + 0.127 + 0.1194 mm (0.3658 mm) | 4.16 | |
| L4 | Copper | 0.0152 mm | 0.5 oz | |
| L4 to L5 | core | 0.3 mm | 4.6 | |
| L5 | Copper | 0.0152 mm | 0.5 oz | |
| L5 to L6 | 2116 prepreg | 0.127 + 0.1194 mm (0.2464 mm) | 4.16 | |
| L6 | Copper | 1.6 mil | 1 oz finished | |
| Mask | Solder mask | 0.6 mil | 3.8 |
Two 2116 plies on the stackup drawing: 0.127 mm, 0.1194 mm. JLCPCB gives no pressed thickness for this build, so the height is their sum, 0.2464 mm. An older JLCPCB impedance page still lists 2116 as 4.25. This preset uses 4.16 from the current stackup page and the capabilities table. JLCPCB does not state the frequency for this εr.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, with mask | 17.24 mil (0.438 mm) | 50.00 Ω | Open |
| 50 Ω microstrip, mask off | 17.95 mil (0.456 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, with mask | 9.64 mil (0.245 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, with mask | 6.86 mil (0.174 mm) | 100.01 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that. JLCPCB's guide says the etched top width is the base width minus 0.7 mil. These widths do not subtract it, so let the coupon decide the last ohm.
The same 50 Ω line on the other 1.6 mm 6-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- JLC06161H-3313: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-7628: 11.66 mil (0.296 mm) over 7.1 mil
- JLC06161H-1080: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-1080A: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-3313A: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-3313B: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-2116B: 7.39 mil (0.188 mm) over 0.1164 mm
- JLC06161H-7628D: 29.64 mil (0.753 mm) over 0.4244 mm
- JLC06161H-2116C: 17.24 mil (0.438 mm) over 0.2464 mm
Sources
- JLCPCB impedance stackup, read 2026-11-12
- JLCPCB impedance parameters, read 2026-11-12
- JLCPCB impedance calculator guide, updated 2026-11-10, read 2026-11-12
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?