JLC06161H-7628 stackup: layers, εr, 50 Ω and 90 Ω widths
JLC06161H-7628 is JLCPCB's 1.6 mm 6-layer build: 7.1 mil of 7628 prepreg at εr 4.4 under layer 1, over a 0.4 mm core. A 50 Ω microstrip on layer 1 is 11.66 mil (0.296 mm) with the solder mask at 1 GHz.
Open JLC06161H-7628 in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | 0.6 mil | 3.8 | |
| L1 | Copper | 1.6 mil | 1 oz finished | |
| L1 to L2 | 7628 prepreg | 7.1 mil | 4.4 | |
| L2 | Copper | 0.0152 mm | 0.5 oz | |
| L2 to L3 | core | 0.4 mm | 4.6 | |
| L3 | Copper | 0.0152 mm | 0.5 oz | |
| L3 to L4 | 7628 prepreg | 8.5 mil | 4.4 | |
| L4 | Copper | 0.0152 mm | 0.5 oz | |
| L4 to L5 | core | 0.4 mm | 4.6 | |
| L5 | Copper | 0.0152 mm | 0.5 oz | |
| L5 to L6 | 7628 prepreg | 7.1 mil | 4.4 | |
| L6 | Copper | 1.6 mil | 1 oz finished | |
| Mask | Solder mask | 0.6 mil | 3.8 |
JLCPCB says to use 7.1 mil for an outer-layer controlled-impedance track. The stackup drawing lists 0.2104 mm. JLCPCB gives 8.1 mil for 7628 when the track is on an inner layer of a 4-layer board. A stripline on layer 2 or 5 of this 6-layer build uses the same figure here. The drawing lists 0.2104 mm. An older JLCPCB impedance page still lists 7628 as 4.6. This preset uses 4.4 from the current stackup page and the capabilities table. JLCPCB does not state the frequency for this εr.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, with mask | 11.66 mil (0.296 mm) | 50.00 Ω | Open |
| 50 Ω microstrip, mask off | 12.31 mil (0.313 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, with mask | 7.50 mil (0.190 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, with mask | 5.42 mil (0.138 mm) | 100.00 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that. JLCPCB's guide says the etched top width is the base width minus 0.7 mil. These widths do not subtract it, so let the coupon decide the last ohm.
The same 50 Ω line on the other 1.6 mm 6-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- JLC06161H-3313: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-7628: 11.66 mil (0.296 mm) over 7.1 mil
- JLC06161H-1080: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-1080A: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-3313A: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-3313B: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-2116B: 7.39 mil (0.188 mm) over 0.1164 mm
- JLC06161H-7628D: 29.64 mil (0.753 mm) over 0.4244 mm
- JLC06161H-2116C: 17.24 mil (0.438 mm) over 0.2464 mm
Sources
- JLCPCB impedance stackup, read 2026-11-12
- JLCPCB impedance parameters, read 2026-11-12
- JLCPCB impedance calculator guide, updated 2026-11-10, read 2026-11-12
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?