JLC06161H-3313 stackup: layers, εr, 50 Ω and 90 Ω widths

JLC06161H-3313 is JLCPCB's 1.6 mm 6-layer build: 3.5 mil of 3313 prepreg at εr 4.1 under layer 1, over a 0.55 mm core. A 50 Ω microstrip on layer 1 is 5.42 mil (0.138 mm) with the solder mask at 1 GHz.

Open JLC06161H-3313 in the Transmission Line Calculator

Layers

LayerMaterialThicknessεrCopper
MaskSolder mask0.6 mil3.8
L1Copper1.6 mil1 oz finished
L1 to L23313 prepreg3.5 mil4.1
L2Copper0.0152 mm0.5 oz
L2 to L3core0.55 mm4.6
L3Copper0.0152 mm0.5 oz
L3 to L42116 prepreg5.5 mil4.16
L4Copper0.0152 mm0.5 oz
L4 to L5core0.55 mm4.6
L5Copper0.0152 mm0.5 oz
L5 to L63313 prepreg3.5 mil4.1
L6Copper1.6 mil1 oz finished
MaskSolder mask0.6 mil3.8

JLCPCB says to use 3.5 mil for an outer-layer controlled-impedance track. The stackup drawing lists 0.0994 mm. JLCPCB gives 4.5 mil for 3313 when the track is on an inner layer of a 4-layer board. A stripline on layer 2 or 5 of this 6-layer build uses the same figure here. The drawing lists 0.0994 mm. An older JLCPCB impedance page still lists 3313 as 4.05. This preset uses 4.1 from the current stackup page and the capabilities table. JLCPCB does not state the frequency for this εr.

Trace widths on layer 1

LineWidthSolvedCalculator
50 Ω microstrip, with mask5.42 mil (0.138 mm)50.00 ΩOpen
50 Ω microstrip, mask off6.00 mil (0.152 mm)50.00 ΩOpen
90 Ω pair, 5 mil gap, with mask4.58 mil (0.116 mm)90.00 ΩOpen
100 Ω pair, 5 mil gap, with mask3.42 mil (0.087 mm)under JLCPCB's 3.5 mil minimum100.00 ΩOpen

Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that. JLCPCB's guide says the etched top width is the base width minus 0.7 mil. These widths do not subtract it, so let the coupon decide the last ohm. JLCPCB's impedance page prints 3.5 mil as the minimum trace width and spacing (read 2026-11-12). A flagged row is under it.

The same 50 Ω line on the other 1.6 mm 6-layer builds

The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.

Sources

How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.

KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?