OSH Park 6-layer stackup: layers, εr, 50 Ω and 90 Ω widths
OSH Park 6-layer is OSH Park's 1.6 mm 6-layer build: 4.36 mil of FR408HR 106 75% prepreg at εr 3.23 under layer 1, over a 4 mil core. A 50 Ω microstrip on layer 1 is 8.46 mil (0.215 mm) with the solder mask at 1 GHz.
Open OSH Park 6-layer in the Transmission Line Calculator
Layers
| Layer | Material | Thickness | εr | Copper |
|---|---|---|---|---|
| Mask | Solder mask | 0.6 mil | 3.9 | |
| L1 | Copper | 1.7 mil | 1 oz finished | |
| L1 to L2 | FR408HR 106 75% prepreg | 4.36 mil | 3.23 | |
| L2 | Copper | 0.0175 mm | 0.5 oz | |
| L2 to L3 | FR408HR 2113 core | 4 mil | 3.66 | |
| L3 | Copper | 0.0175 mm | 0.5 oz | |
| L3 to L4 | FR408HR core | 36.44 mil | Not printed | |
| L4 | Copper | 0.0175 mm | 0.5 oz | |
| L4 to L5 | FR408HR 2113 core | 4 mil | 3.66 | |
| L5 | Copper | 0.0175 mm | 0.5 oz | |
| L5 to L6 | FR408HR 106 75% prepreg | 4.36 mil | 3.23 | |
| L6 | Copper | 1.7 mil | 1 oz finished | |
| Mask | Solder mask | 0.6 mil | 3.9 |
The stackup table prints 4.36 mil (0.1107 mm) between layer 1 and layer 2. OSH Park states the prepreg and core Dk at 1 GHz. The mask Dk on the construction diagram carries no frequency.
The table prints no Dk for the solder resist. The construction diagram prints 3.90 for the purple Taiyo mask at 0.60 mil, and this preset uses that. Copper: the table prints 1.7 mil outer and 0.68 mil (0.0175 mm) inner; the diagram prints 1.80 and 0.60 mil. This preset uses the table.
Trace widths on layer 1
| Line | Width | Solved | Calculator |
|---|---|---|---|
| 50 Ω microstrip, with mask | 8.46 mil (0.215 mm) | 50.00 Ω | Open |
| 50 Ω microstrip, mask off | 9.16 mil (0.233 mm) | 50.00 Ω | Open |
| 90 Ω pair, 5 mil gap, with mask | 6.65 mil (0.169 mm) | 90.00 Ω | Open |
| 100 Ω pair, 5 mil gap, with mask | 5.02 mil (0.128 mm) | 100.00 Ω | Open |
Bare copper at 1 GHz, from a 2-D field solve of the cross-section with the mask coating the trace top and sidewalls. The 5 mil gap is a typed value, because the stackup leaves the gap to you. Ask the fab what space it will etch, then open the row and type that.
OSH Park's own impedance table
| Target | OSH Park width | Gap | OSH Park predicts | This page |
|---|---|---|---|---|
| 50 Ω single | 8.3 mil | 50.1 Ω | 8.46 mil | |
| 90 Ω pair | 6.8 mil | 5.2 mil | 89.6 Ω | 6.65 mil |
| 100 Ω pair | 5.7 mil | 6.3 mil | 100.1 Ω | 5.02 mil |
The impedance table on OSH Park's service page lists its own layer-1 widths with the mask. Its pairs use their own gap, which is not always 5 mil, so open a row above and type their gap to compare a pair exactly.
Substitute-material builds
OSH Park has built some orders on EM528 during FR408HR shortages. The mixed 6-layer build (June and late July 2026) keeps this 106 prepreg and both 2113 cores and swaps only the centre for a 21 mil EM-528 core at Dk 4.11, so the layer-1 widths here still apply. The alternate-stackup page, which offers an EM528 core at checkout since 2026-09-21, prints no 6-layer build, so ask OSH Park what sits under layer 1 if you pick it.
What OSH Park does not print
No typical number fills these, and none of them sets a width on this page.
- The Dk of the 36.44 mil centre layer between L3 and L4. The table calls it FR408HR core and prints no Dk. The construction diagram draws it as 7.96 mil of 2113 prepreg (Dk 3.61), a 21 mil core (3.79) and 7.96 mil of prepreg (3.61), 36.92 mil in all, and prints no combined Dk. It stays blank, and no stripline is built across it.
- The frequency of the solder mask Dk. The construction diagram prints 3.90 with no frequency; the prepreg and core Dk are stated at 1 GHz.
The same 50 Ω line on the other 6-layer builds
The prepreg under layer 1 sets the width. A thinner prepreg gives a narrower line for the same impedance, and builds with the same prepreg under layer 1 give the same width.
- JLC06161H-3313: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-7628: 11.66 mil (0.296 mm) over 7.1 mil
- JLC06161H-1080: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-1080A: 4.69 mil (0.119 mm) over 0.0764 mm
- JLC06161H-3313A: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-3313B: 5.42 mil (0.138 mm) over 3.5 mil
- JLC06161H-2116B: 7.39 mil (0.188 mm) over 0.1164 mm
- JLC06161H-7628D: 29.64 mil (0.753 mm) over 0.4244 mm
- JLC06161H-2116C: 17.24 mil (0.438 mm) over 0.2464 mm
- PCBWay 6-layer 1.6 mm 70%: 7.91 mil (0.201 mm) mask off over 0.1195 mm
- PCBWay 6-layer 1.6 mm 50%: 11.59 mil (0.294 mm) mask off over 0.1785 mm
- PCBWay 6-layer 1.6 mm 30%: 6.90 mil (0.175 mm) mask off over 0.1055 mm
- OSH Park 6-layer: 8.46 mil (0.215 mm) over 4.36 mil
Sources
- OSH Park 6 layer service, read 2026-11-15
- OSH Park 6-layer construction diagram, read 2026-11-15
- OSH Park alternate multilayer stackup, read 2026-11-15
- OSH Park mixed-substrate stackup, read 2026-11-15
How IndieRF checks its numbers: each engine against an outside answer, with the tolerance and what it does not cover.
KiCad vs JLCPCB 50 Ω width90 Ω USB pair width50 Ω microstrip width on FR-4Question about this stackup, or a correction?