28 GHz 5G transmitter lineup: 44.5 dBm EIRP with 8.7 dB P1dB headroom
A 1 GHz IF DAC, upconverter, driver, PA and output filter deliver 26.0 dBm to the 18.5 dBi array: 44.5 dBm EIRP. The drive sits 8.7 dB under the chain's 1 dB compression point, and cascaded OIP3 is 44.7 dBm.
Change this: a PA with 33 dBm P1dB instead of 36. Headroom reads 5.83 dB; it moves 2.84 dB and not the full 3, because the driver also compresses.
OIP3 44.65 dBm: 28 GHz Power Amplifier sets it, 11.15 dB better if ideal, 92% of 1/OIP3.
Block diagram
Level diagram
Budget at FR2 Phased Array
| Row | Value |
|---|---|
| Cumulative Gain | 32.00 dB |
| Source Contribution | 25.98 dBm |
| EIRP | 44.48 dBm |
| SNR | 69.99 dB |
| Noise Density | −124.01 dBm/Hz |
| Total Noise Power | −44.01 dBm |
| Output Noise Relative to Carrier | −149.99 dBc/Hz |
| P1dB Headroom | 8.67 dB |
| Cumulative OIP3 | 44.65 dBm |
| Cumulative IIP3 | 12.65 dBm |
| Cumulative OP1dB | 33.67 dBm |
| Cumulative IP1dB | 2.67 dBm |
| First Stage to Compress OP1dB | 34.00 dBm |
| SFDR | 59.11 dB |
| IM3 | −11.37 dBm |
| Cumulative Noise + Distortion Ratio | 37.34 dB |
| Fully Linear Power | 26.00 dBm |
| Local Compression | 0.00 dB |
| Cumulative Compression | 0.02 dB |
Every number here is the analyzer's own, solved when the site was built from the same template the button opens. How the solver is checked.
Model limits
- The solver is unidirectional and matched: no mismatch interaction, return-loss cascade or stability.
- Noise density, NF, compression, gain and IM3 are read at each block's stage frequency, not solved across the operating band.
- A filter or any part with a frequency curve shapes noise inside the selected channel only: integrated noise, SNR and the noise floor integrate the curve across the channel, and Noise Density and NF stay spot values at its centre. A part with no curve is a scalar loss and NF. Noise outside the channel, such as an ADC's alias zones, is not counted.
- Mixer image noise in the NF is one point per band: the image band runs through every block upstream and is read at its centre as a spot density. Behind a curve the integrated noise rows carry the image channel point by point, so a filter skirt across it counts there.
- LO phase noise sets a scalar LO noise density. It is not integrated through the mixer. A phase noise mask gives integrated phase error, jitter and an EVM floor as scalar rows and a reciprocal-mixing estimate in the blocker panel; no noise row reads it.
- Distortion is IM3 only, and IM3 is not frequency resolved.
- Compression is a memoryless AM/AM curve: no AM/PM, bias or memory effects. Noise keeps the small-signal gain under a blocker.
Other solved chains
- 2.45 GHz superheterodyne receiver: 3.36 dB NF and −85.4 dBm sensitivity
- Direct-sampling SDR receiver at 1.2 GHz: 4.45 dB NF with 18.8 dB of ADC headroom
- LoRa 915 MHz receiver front end: 4.66 dB NF with an LNA after the filter
- ADS-B 1090 MHz receiver, filter first: 4.99 dB NF
- ADS-B 1090 MHz receiver, LNA first: 2.65 dB NF
- 2.4 GHz chip-antenna receiver: 8.00 dB NF and −94.0 dBm sensitivity
- Ka-band 28.5 GHz transmitter lineup: 57.1 dBm EIRP with 6.2 dB P1dB headroom
- 2-way Wilkinson power-combining PA at 2.2 GHz: 36.5 dBm out, OIP3 51.0 dBm