Ka-band 28.5 GHz transmitter lineup: 57.1 dBm EIRP with 6.2 dB P1dB headroom
A 1 GHz IF upconverts against the LO, and the driver, PA, output filter and interconnect feed a 30 dBi aperture: 57.1 dBm EIRP from 27.6 dBm conducted, 6.2 dB under cascaded P1dB. This page reads the 28.5 GHz point; every part follows its curve, and the template sweeps 27.5 to 31 GHz.
Change this: the interconnect from 0.12 to 0.3 m. EIRP reads 56.73 dBm; at 28.5 GHz each 10 cm of this line costs 0.21 dB.
OIP3 44.23 dBm: Ka Power Amplifier sets it, 13.23 dB better if ideal, 95% of 1/OIP3.
Block diagram
Level diagram
Budget at Ka Aperture Antenna
| Row | Value |
|---|---|
| Cumulative Gain | 32.88 dB |
| Source Contribution | 27.61 dBm |
| EIRP | 57.11 dBm |
| SNR | 73.86 dB |
| Noise Density | −123.24 dBm/Hz |
| Total Noise Power | −46.25 dBm |
| Output Noise Relative to Carrier | −150.85 dBc/Hz |
| P1dB Headroom | 6.23 dB |
| Cumulative OIP3 | 44.23 dBm |
| Cumulative IIP3 | 11.36 dBm |
| Cumulative OP1dB | 32.90 dBm |
| Cumulative IP1dB | 1.03 dBm |
| First Stage to Compress OP1dB | 33.15 dBm |
| SFDR | 60.32 dB |
| IM3 | −5.63 dBm |
| Cumulative Noise + Distortion Ratio | 33.24 dB |
| Fully Linear Power | 27.68 dBm |
| Local Compression | 0.00 dB |
| Cumulative Compression | 0.06 dB |
Every number here is the analyzer's own, solved when the site was built from the same template the button opens. How the solver is checked.
Model limits
- The solver is unidirectional and matched: no mismatch interaction, return-loss cascade or stability.
- Noise density, NF, compression, gain and IM3 are read at each block's stage frequency, not solved across the operating band.
- A filter or any part with a frequency curve shapes noise inside the selected channel only: integrated noise, SNR and the noise floor integrate the curve across the channel, and Noise Density and NF stay spot values at its centre. A part with no curve is a scalar loss and NF. Noise outside the channel, such as an ADC's alias zones, is not counted.
- Mixer image noise in the NF is one point per band: the image band runs through every block upstream and is read at its centre as a spot density. Behind a curve the integrated noise rows carry the image channel point by point, so a filter skirt across it counts there.
- LO phase noise sets a scalar LO noise density. It is not integrated through the mixer. A phase noise mask gives integrated phase error, jitter and an EVM floor as scalar rows and a reciprocal-mixing estimate in the blocker panel; no noise row reads it.
- Distortion is IM3 only, and IM3 is not frequency resolved.
- Compression is a memoryless AM/AM curve: no AM/PM, bias or memory effects. Noise keeps the small-signal gain under a blocker.
Other solved chains
- 2.45 GHz superheterodyne receiver: 3.36 dB NF and −85.4 dBm sensitivity
- Direct-sampling SDR receiver at 1.2 GHz: 4.45 dB NF with 18.8 dB of ADC headroom
- LoRa 915 MHz receiver front end: 4.66 dB NF with an LNA after the filter
- ADS-B 1090 MHz receiver, filter first: 4.99 dB NF
- ADS-B 1090 MHz receiver, LNA first: 2.65 dB NF
- 2.4 GHz chip-antenna receiver: 8.00 dB NF and −94.0 dBm sensitivity
- 28 GHz 5G transmitter lineup: 44.5 dBm EIRP with 8.7 dB P1dB headroom
- 2-way Wilkinson power-combining PA at 2.2 GHz: 36.5 dBm out, OIP3 51.0 dBm