Published Nov 7, 2026 · Last updated Nov 7, 2026 · 6 min · IndieRF

Coax Loss at 2.4 GHz: LMR-400 Keeps 61 W, RG-58 4.5 W

Ten meters of LMR-400 loses 2.17 dB at 2.4 GHz and delivers 61 W of 100 W; the same run of RG-58 loses 13.5 dB and delivers 4.5 W. The RG-58, RG-8X and RG-174 sheets stop at 1 GHz, so their 2.4 GHz numbers are extrapolated, and a lossy cable makes a 2:1 antenna read better at the radio than it is.

Ten meters of LMR-400 loses 2.17 dB at 2.4 GHz, so 100 W into the cable is 61 W at the antenna. The same 10 m of RG-58 loses 13.5 dB and delivers 4.5 W, which turns a 100 W amplifier into a 5 W one. For a Wi-Fi or 2.4 GHz feed longer than a jumper, buy LMR-400 or bigger, and keep thin cable for pigtails under a meter.

Ten meters of each common cable at 2.4 GHz

Each number is matched loss from the maker's printed attenuation table. The coax pages fit every table as α=af+bf\alpha = a\sqrt{f} + b f, conductor loss plus dielectric loss, and read the fit at 2400 MHz. Watts out is 100×10−L/10100 \times 10^{-L/10} for a loss LL in dB, so every 3 dB halves the watts.

CabledB per 10 mW out of 100 W2.4 GHz on the sheet
LMR-6001.4272.1printed
LMR-4002.1760.6printed
LMR-2404.1638.4printed
RG-213 (Belden 8267)4.8332.9printed
LMR-1956.1024.5printed
RG-8X (Belden 9258)6.3623.1extrapolated
LMR-100A12.765.29printed
RG-58 (Belden 8262)13.484.49extrapolated
RG-316 (Belden 83284)15.502.82printed
RG-174 (Belden 8216)19.761.06extrapolated

LMR-400 keeps about 60% of the power, LMR-240 about 40%, and LMR-195 a quarter. The cable names are part numbers, each with one datasheet: "RG-58" here is Belden 8262, and another maker's RG-58 has its own table.

In the clip, LMR-400 reads 2.17 dB and 60.6 W and RG-58 reads 13.48 dB, extrapolated, at 2.4 GHz, and with the cursor dragged to 5.8 GHz RG-58 has no number, past its 4 GHz limit.

Every cable at 2.4 GHz and 10 m from the first link in the coax cable explorer, with LMR-400 and RG-58 (Belden 8262) picked and the frequency cursor dragged to 5.8 GHz.

Three of these are past their datasheet

Belden prints RG-58, RG-8X and RG-174 only up to 1 GHz. At 2.4 GHz the explorer carries the same fit 2.4 times past the last row, draws it dashed, and labels the number extrapolated. The fit holds up that far. Fitted on its rows up to 1 GHz, Belden's RG-316 predicts its own printed 2.4 GHz row within about 2%, and LMR-400 predicts its 2.5 GHz row within about 1%. On RG-58's 13.5 dB, 2% is 0.3 dB, which changes nothing about which cable to buy.

The LMR, RG-213 and RG-316 sheets print rows past 2.4 GHz, so those numbers sit inside the table. Belden prints a 2400 MHz row for RG-316 itself: 47.2 dB per 100 ft, 15.49 dB per 10 m, and the fit reads 15.50.

The fit stops at the lowest of four times the last printed row, the TE11 cutoff and the rated maximum. At 5.8 GHz that puts RG-58, RG-8X and RG-174 past their 4 GHz limit, and the explorer shows the limit instead of a bar.

What to buy

Swapping 10 m of RG-58 for LMR-400 buys 11.3 dB. In a link budget that is 11.3 dB of margin, and in free space it is 3.7 times the range. LMR-195 is half the diameter of LMR-400 and loses 2.8 times as much, so the thin cable earns its place only where the run is short or has to bend tight.

I buy LMR-400 for any run past a few meters and put RG-316 only on the last pigtail. One meter of RG-316 is 1.55 dB, and for that Belden rates it to a 1 in installed bend.

Every number on this page is cable only. Connectors and adapters add their own loss and their own match, and neither the explorer nor Coax Loss counts them.

SWR at the radio looks better than at the antenna

A reflection crosses the cable twice, so the radio sees the antenna's reflection reduced by twice the matched loss LL:

∣Γradio∣=∣Γant∣⋅10−2L/20|\Gamma_\mathrm{radio}| = |\Gamma_\mathrm{ant}| \cdot 10^{-2L/20}

A 2:1 antenna has ∣Γ∣=1/3|\Gamma| = 1/3, or 9.5 dB return loss. Through 10 m of LMR-400 the reflection loses 4.3 dB more, and the radio reads 13.9 dB return loss, 1.51:1. Through 10 m of RG-58 it loses 27 dB, and the radio reads 1.03:1. That looks like a perfect antenna. It is a 13.5 dB attenuator.

This is the pad rule from the bench: a pad buys twice its value in return loss, and a lossy cable is a pad. It stops at the cable's own match and the connectors', which set a floor this model leaves out. Read SWR at the antenna end, or work the radio reading back through the cable. On Coax Loss a 1.5:1 reading at the radio through 10 m of LMR-400 is a 1.98:1 antenna.

What the 2:1 costs

2:1 VSWR is about half a dB of mismatch loss, 0.51 dB. On a cable, Coax Loss adds the ARRL extra line loss for a load VSWR SS, with A=10L/10A = 10^{L/10} and ρ=(S−1)/(S+1)\rho = (S-1)/(S+1):

PinPload=A2−ρ2A (1−ρ2)\frac{P_\mathrm{in}}{P_\mathrm{load}} = \frac{A^2 - \rho^2}{A\,(1 - \rho^2)}
10 m at 2.4 GHz, 2:1 antennaVSWR at the radioARRL extra (dB)Total loss (dB)W at the antenna
LMR-4001.510.332.5056.2
LMR-2401.290.444.6034.7
LMR-1951.180.486.5822.0
RG-58 (Belden 8262)1.030.5113.993.99

On LMR-400 the 2:1 antenna costs 0.33 dB, 56 W at the antenna instead of 61. On RG-58 the extra reaches the 2:1 rule's 0.51 dB, because nearly all the reflected power dies in the cable on its way back. Either way the antenna is worth a third to a half of a dB, and the cable choice is worth 2 to 11. I fix the cable before the antenna for that reason.

The expression treats the 100 W as the power the line accepts. It is the extra line loss for one load VSWR, and the radio's own source match and any power foldback at 1.51:1 sit outside it.

References

  • Times Microwave Systems, LMR-100A, LMR-195, LMR-240, LMR-400 and LMR-600 data sheets: attenuation tables to 8 GHz.
  • Belden technical data sheets 8262 (RG-58), 9258 (RG-8X), 8216 (RG-174), 8267 (RG-213) and 83284 (RG-316).
  • The ARRL Antenna Book, transmission lines chapter: additional line loss due to SWR.

Questions? Contact

Discussion

No comments yet. Start the thread with a measurement, a correction, or a worked example.